Cisco Cisco IOS Software Release 12.2(11)YT
10
Release Notes for Cisco 2600 Series Routers for Cisco IOS Release 12.2(11) YT2
OL-3286-01 Rev. B0
Caveats for Cisco IOS Release 12.2(11) YT2
Resolved Caveats—Cisco IOS Release 12.2(11) YT2
All the caveats listed in this section originated in Cisco IOS Release 12.2(11)YT and are resolved in
Cisco IOS Release 12.2(11) YT1. This section describes only severity 1 and 2 caveats and select severity
3 caveats.
Cisco IOS Release 12.2(11) YT1. This section describes only severity 1 and 2 caveats and select severity
3 caveats.
Open Caveats—Cisco IOS Release 12.2(11) YT1
This section documents possible unexpected behavior by Cisco IOS Release 12.2(11) YT and are
reported in Cisco IOS Release 12.2(11) YT1. This section describes only severity 1 and 2 caveats and
select severity 3 caveats.
reported in Cisco IOS Release 12.2(11) YT1. This section describes only severity 1 and 2 caveats and
select severity 3 caveats.
Table 6
Resolved Caveats in Cisco IOS Release 12.2(11)YT2
Resolved In
DDTS ID Number
Description
Caveats Originating in Cisco IOS Release 12.2(11)YT That Were Reported in Cisco IOS Release 12.2(11)YT2
12.2(11)YT2
CSCdz76888
app-h450-transfer.2.0.0.x.tcl cannot handle pre-connect disc w/ PI=8
Symptom: Disconnect with pi8 is used pretty often in the PSTN world to cut the
voice path before disconnecting. This function is missing while the H.450.*
application is configured on dial-peers: if the terminating call legs get disconnected
with pi8, the originator will be stuck.
voice path before disconnecting. This function is missing while the H.450.*
application is configured on dial-peers: if the terminating call legs get disconnected
with pi8, the originator will be stuck.
Workaround: There is no workaround.
12.2(11)YT2
CSCdz83896
CEF Switching gets disabled with CRTP on ATM-AIM-T1 interface
Symptom: Enabling CRTP on the ATM-AIM voice interface card disables Fast
Switching and CEF switching. CRTP works fine with process switching.
Switching and CEF switching. CRTP works fine with process switching.
Workaround: If you enable CRTP, use process switching. CRTP works fine with
process switching.
process switching.
12.2(11)YT2
CSCdz84504
E1/0 is not coming up correctly after interface goes down.
Symptom: Controller e1 0 is not coming up correctly after the interface goes down
or the cable is removed.
or the cable is removed.
Conditions: This symptom is observed on a Cisco 2610XM series router with AIM
card and WIC and the commands network-clock participate and network-clock
select.
card and WIC and the commands network-clock participate and network-clock
select.
Workaround: Reload the router. Use an HDM module or disable the network-clock
participate and network-clock select commands.
participate and network-clock select commands.
12.2(11)YT2
CSCea02389
fix localization dependence on SCCP version
Problem: The User Locales do not work when a phone from an 3.3(2) CM falls back
to a SRST router running a 15T image.
to a SRST router running a 15T image.
Symptom: During SRST the user locales on IP Phone won't be available because of
an SCCP version conflict between the CCM 3.3(2) phone loads and SRST locales
dependencies on the SCCP version.
an SCCP version conflict between the CCM 3.3(2) phone loads and SRST locales
dependencies on the SCCP version.
Workaround: There is no workaround.