Cisco Cisco IOS Software Release 12.4(15)XM
![Cisco](https://files.manualsbrain.com/attachments/7380d0050044647c30f5c24bbbf5d0c0b6d9bb84/common/fit/150/50/faa183d287233c52228cfea3dbc2a127fe780f60564fcb0955d9c3d1cd23/brand_logo.png)
28
Release Notes for the Cisco Mobile Wireless Home Agent Feature in Cisco IOS Release 12.4(15)XM2
Caveats
•
CSCsm17204—Access-reject Not Being Sent For a Non-reverse Tunneled User
Ideally, the Home Agent will reject the RRQ if Reverse-Tunnel is not requested by the user and
hotlining policy is downloaded for the user.
hotlining policy is downloaded for the user.
The current behavior is that when there is an access-accept and the hotlining policy is downloaded,
the debug displays that the user is made hotline active, but the binding is not hotlined.
the debug displays that the user is made hotline active, but the binding is not hotlined.
Workaround: reverse tunneling should be enabled for a hotlined user.
•
CSCsm34309— Issue with Conditional Debugging for Hotlined User
When a hotlined user is brought back to normal , and conditional debugging is on for RADIUS
debugs of the accounting stop/start pair, we only see a RADIUS accounting stop message. The
“Accounting Start” message is not displayed.
debugs of the accounting stop/start pair, we only see a RADIUS accounting stop message. The
“Accounting Start” message is not displayed.
Workaround: none.
•
CSCsm38451—HA R4.0: Tracebacks found on HA for every upstream packet
For every upstream packet through the MIP/LAC tunnel, a traceback occurs.
This happens only when the packet is switched through process path (most likely, when both CEF
and fast switching are disabled through CLI).
and fast switching are disabled through CLI).
Workaround: do not disable fast and CEF switching.
•
CSCsm38957— clear ip mob bin all sync Initiates del sync Request to the Standby for MIPLAC
A delete sync request message occurs from active to standby for MIPLAC bindings. This is seen on
the counters of the show ip mobile traffic command. There is no impact.
the counters of the show ip mobile traffic command. There is no impact.
When a MIPLAC session is cleared with clear ip mobile binding all sync, it initates delete sync
request to standby.
request to standby.
Workaround: none.
•
CSCsm41386—Memory Leak Found During the long run of MIP-LAC test
Memory leak and memory leak chunks are noticed after 8 hours of MIP-LAC testing involving
registration / re-registration of 8K MIP-LAC sessions.
registration / re-registration of 8K MIP-LAC sessions.
This happens after 8 hours of MIP-LAC testing (opening 8K MIP-LAC sessions and leave them open
for 8 hours).
for 8 hours).
Workaround: none.
•
CSCsm45543—Framed IP Address Attribute is Missing in Access-Request
On a Cisco router running Release 4.0 HA software, the framed IP address attribute is missing in an
access request when opening a MIP flow of Wimax.
access request when opening a MIP flow of Wimax.
This occurs when opening a MIP flow of WiMAX type only.
Workaround: none.
•
CSCsm45978-RRQ-MN-HA-SPI Attribute 19 and 20 Bindings Do Not Come Up (WIMAX)
Bindings are coming up when using WIMAX attributes 19 and 20 MN-RRQ-HA-IP .
This condition occurs when you configure attribute 19 and 20 in RSIM. The bindings are not seen.
Workaround: none.
•
CSCsm46468—Mem Leak Found During QoS Testing in Both Active and Standby HA
On a Cisco router running the HA 4.0 release software, memory leaks are seen in both active and
standby HA when a switchover is triggered during a QoS stress test.
standby HA when a switchover is triggered during a QoS stress test.
Workaround: none