Cisco Cisco IOS Software Release 12.2(33)SRE
166
Caveats for Cisco IOS Release 12.2(33)SRE through 12.2(33)SRE13
OL-10394-05 Rev. S1
•
CSCui65914
Symptom: Minor or major temperature alarms are reported in the syslog along with the following
DATACORRUPTION logs:
DATACORRUPTION logs:
Aug 5 15:54:30.972 Buc: DATACORRUPTION-SP-1-DATAINCONSISTENCY copy error, -PC=
0x414DEED4z -Traceback= 4027C4F4 419551C0 414DEED4 414E5BC4 414E0CA0 414E0F00 Aug 5
15:54:30.972 Buc: C6KENV-SP-4-MINORTEMPALARM interface 10/0 outlet temperature crossed
threshold #1(=60C). It has exceeded normal operating temperature range.
Conditions: The symptom is observed on ES+ series linecards of Cisco 7600 Series Routers.
Workaround: There is no workaround.
•
CSCuj30702
Symptom: This bug is specific to port channel sub interface configuration in ES+ card. This bug is
not relevant to any other port channel configuration in ES+, that is, EVC/Bridge-Domain over PoCH
sub-int etc, and other card types, such as ES20/ LAN cards are free from this bug. Any type of IP
communication on port channel sub interfaces in ES+ cards fail. Such an issue is seen only with port
channel sub interfaces on ES+ and not seen with port channel main interfaces.
not relevant to any other port channel configuration in ES+, that is, EVC/Bridge-Domain over PoCH
sub-int etc, and other card types, such as ES20/ LAN cards are free from this bug. Any type of IP
communication on port channel sub interfaces in ES+ cards fail. Such an issue is seen only with port
channel sub interfaces on ES+ and not seen with port channel main interfaces.
Conditions: This symptom will only be seen with images where the fix of CSCuh40617 is integrated.
Workaround: The connections will work fine if it is moved to the main interface or by using EVC
BD configurations.
BD configurations.
•
CSCuj82897
Symptom: The “control-word” length is not set properly for small HDLC packets running over
HDLC AToM VC with SIP-200. For example: SPA-8XCHT1/E1.
HDLC AToM VC with SIP-200. For example: SPA-8XCHT1/E1.
Conditions: This symptom occurs when HDLC AToM VC with SIP-200 is deployed, for example,
SPA-8XCHT1/E1, will result in a packet length mismatch issue or dropping by the remote PE router
when HDLCoverMPLS runs over the Ethernet link adding an additional padding which cannot be
classified at all.
SPA-8XCHT1/E1, will result in a packet length mismatch issue or dropping by the remote PE router
when HDLCoverMPLS runs over the Ethernet link adding an additional padding which cannot be
classified at all.
Workaround: Use SIP-400.
•
CSCul27327
Symptom: On the Cisco c7600 router, if PIM is configured on the port-channel and on the port
members, any failure on one of the port members will disable the FE CAM.
members, any failure on one of the port members will disable the FE CAM.
Conditions: This symptom occurs when PIM is configured on the port members.
Workaround: Perform the following workaround:
1.
Do not configure PIM sparse-mode on the port members even though the CLI is accepted.
2.
In case the PIM sparse-mode is configured on the port members, remove it from the port
members and the port-channel and then reapply the PIM configuration on the port-channel only.
members and the port-channel and then reapply the PIM configuration on the port-channel only.
Further Problem Description: A similar issue (CSCtf75608) is seen on the Cisco Catalyst 6500
Series Switches, but the workaround is to configure PIM on the port-channel and the port members
to avert the FE CAM to be disabled in the event of one of the port members failing.
Series Switches, but the workaround is to configure PIM on the port-channel and the port members
to avert the FE CAM to be disabled in the event of one of the port members failing.
•
CSCul52239
Symptom: Multicast traffic might get affected after an interface delete and reconfiguration. This is
more likely to happen in dot1q sub-interfaces in ES+ and specifically only if the delete and
reconfiguration of the interface is done within 30 seconds.
more likely to happen in dot1q sub-interfaces in ES+ and specifically only if the delete and
reconfiguration of the interface is done within 30 seconds.
Conditions: This symptom occurs in Cisco IOS Release 12.2SREx and Cisco IOS 15S based
releases.
releases.
Workaround: Perform interface delete and reconfiguration with a time gap of one minute.