Cisco Cisco IOS Software Release 12.2(33)SRE
1400
Caveats for Cisco IOS Release 12.2(33)SRA through 12.2(33)SRA7
OL-10394-05 Rev. R0
frame-relay intf-type dce
Debug frame lmi
MFR1(up): DCE LMI timeout
MFR1: Invalid LMI type 1
MFR1(down): DCE LMI timeout
MFR1: Invalid LMI type 1
MFR1: Invalid LMI type 1
MFR1(down): DCE LMI timeout
MFR1: Invalid LMI type 1
MFR1(down): DCE LMI timeout
MFR1: Invalid LMI type 1
MFR1: Invalid LMI type 2
MFR1(down): DCE LMI timeout
•
CSCsj91961
Symptoms: When you first create the channels for an E3 interface in a particular order on the active
supervisor engine and then the standby supervisor engine is reloaded, the ifNumber objects on the
active and standby supervisor engines do not match. This situation prevents proper forwarding on
the E3 interface after a switchover.
supervisor engine and then the standby supervisor engine is reloaded, the ifNumber objects on the
active and standby supervisor engines do not match. This situation prevents proper forwarding on
the E3 interface after a switchover.
Conditions: This symptom is observed on a Cisco 7600 series that is configured with an Enhanced
FlexWAN.
FlexWAN.
Workaround: Reload the router after you have configured the channels for the E3 interface.
•
CSCsk08765
Symptoms: When you add the first link to a multilink or MFR bundle, a bus error crash may occur,
and the following error message is generated:
and the following error message is generated:
TLB (load or instruction fetch) exception, CPU signal 10
Conditions: This symptom is observed on a Cisco 7600 series that runs Cisco IOS
Release 12.2(33)SRA, Release 12.2(33)SRB1, or Release 12.2SXF when you first have attached a
policy map to the multilink or MFR interface and then have added the first link to the bundle.
Release 12.2(33)SRA, Release 12.2(33)SRB1, or Release 12.2SXF when you first have attached a
policy map to the multilink or MFR interface and then have added the first link to the bundle.
Workaround: First, add the required number of links to the multilink or MFR interface. Then, attach
the service policy to the multilink or MFR interface.
the service policy to the multilink or MFR interface.
•
CSCsk14208
Symptoms: A WAN line card or module that is configured for WCCP Redirection via the ip wccp
web-cache redirect {out | in} interface configuration command may not redirect packets to the
Cache Engine after an OIR has occurred or after the line card or module has been reloaded.
web-cache redirect {out | in} interface configuration command may not redirect packets to the
Cache Engine after an OIR has occurred or after the line card or module has been reloaded.
Conditions: This symptom is observed on a Cisco Catalyst 6000 series switch and Cisco 7600 series
router when WCCP redirection is applied to the interfaces that are configured on the WAN line card
or module.
router when WCCP redirection is applied to the interfaces that are configured on the WAN line card
or module.
Workaround: Remove and re-apply the WCCP Redirection configuration to the affected WAN
interfaces by entering the no ip wccp web-cache redirect {out | in} interface configuration
command followed by the ip wccp web-cache redirect {out | in} interface configuration command.
interfaces by entering the no ip wccp web-cache redirect {out | in} interface configuration
command followed by the ip wccp web-cache redirect {out | in} interface configuration command.
Alternate Workaround: Delete and configure WCCP Redirection globally on the router by entering
the no ip wccp web-cache router configuration command followed by the ip wccp web-cache
router configuration command.
the no ip wccp web-cache router configuration command followed by the ip wccp web-cache
router configuration command.