Cisco Cisco IOS Software Release 12.2(55)SE
![Cisco](https://files.manualsbrain.com/attachments/7380d0050044647c30f5c24bbbf5d0c0b6d9bb84/common/fit/150/50/faa183d287233c52228cfea3dbc2a127fe780f60564fcb0955d9c3d1cd23/brand_logo.png)
8
Release Notes for Catalyst 2350 Switch, Cisco IOS Release 12.2(55)SE and Later
OL-23019-05
Limitations and Restrictions
•
When the configuration file is removed from the switch and the switch is rebooted, port status for
VLAN 1 and the management port (Fast Ethernet 0) is sometimes reported as
VLAN 1 and the management port (Fast Ethernet 0) is sometimes reported as
up
and sometimes as
down
, resulting in conflicts. This status depends on when you respond to the reboot query:
Would you like to enter the initial configuration dialog?
–
After a reboot if you wait until the Line Protocol status of VLAN 1 appears on the console
before responding, VLAN 1 line status is always shown as
before responding, VLAN 1 line status is always shown as
down
. This is the correct state.
–
The problem (VLAN 1 reporting
up
) occurs if you respond to the query before VLAN 1 line
status appears on the console.
The workaround is to wait for approximately 1 minute after rebooting and until the VLAN 1
interface line status appears on the console before you respond to the query. (CSCsl02680)
interface line status appears on the console before you respond to the query. (CSCsl02680)
Multicasting
•
When you configure the ip igmp max-groups number and ip igmp max-groups action replace
interface configuration commands and the number of reports exceed the configured max-groups
value, the number of groups might temporarily exceed the configured max-groups value. No
workaround is necessary because the problem corrects itself when the rate or number of IGMP
reports are reduced. (CSCse27757)
interface configuration commands and the number of reports exceed the configured max-groups
value, the number of groups might temporarily exceed the configured max-groups value. No
workaround is necessary because the problem corrects itself when the rate or number of IGMP
reports are reduced. (CSCse27757)
•
When you configure the IGMP snooping throttle limit by using the ip igmp max-groups number
interface configuration on a port-channel interface, the groups learned on the port-channel might
exceed the configured throttle limit number, when all of these conditions are true:
interface configuration on a port-channel interface, the groups learned on the port-channel might
exceed the configured throttle limit number, when all of these conditions are true:
–
The port-channel is configured with member ports across different switches in the stack.
–
When one of the member switches reloads.
–
The member switch that is reloading has a high rate of IP IGMP joins arriving on the
port-channel member port.
port-channel member port.
The workaround is to disable the IGMP snooping throttle limit by using the no ip igmp max-groups
number interface configuration command and then to reconfigure the same limit again.
(CSCse39909)
number interface configuration command and then to reconfigure the same limit again.
(CSCse39909)
QoS
•
When QoS is enabled and the egress port receives pause frames at the line rate, the port cannot send
packets.
packets.
There is no workaround. (CSCeh18677)
•
Egress shaped round robin (SRR) sharing weights do not work properly with system jumbo MTU
frames.
frames.
There is no workaround. (CSCsc63334)
•
In a hierarchical policy map, if the VLAN-level policy map is attached to a VLAN interface and the
name of the interface-level policy map is the same as that for another VLAN-level policy map, the
switch rejects the configuration, and the VLAN-level policy map is removed from the interface.
name of the interface-level policy map is the same as that for another VLAN-level policy map, the
switch rejects the configuration, and the VLAN-level policy map is removed from the interface.
The workaround is to use a different name for the interface-level policy map. (CSCsd84001)
•
If the ingress queue has low buffer settings and the switch sends multiple data streams of system
jumbo MTU frames at the same time at the line rate, the frames are dropped at the ingress.
jumbo MTU frames at the same time at the line rate, the frames are dropped at the ingress.
There is no workaround. (CSCsd72001)