Samsung SSC-5000P Manuel D’Utilisation
8_ installation
installation
INSTALLATION ENVIRONMENT SETUP
The following information is prepared for safe installation of the unit.
This unit can be placed on a flat table or installed in the rack.
It should not be used vertically or skew, but horizontally.
It should not be used vertically or skew, but horizontally.
The location of the unit and the composition of wiring are very important in properly operating the system.
When equipment is placed too close or if ventilation is not properly done, system may not work properly, and
maintenance of the system may be difficult.
In order to prevent system failure and to reduce system shut-down by outside environmental factors, air
circulation in the system operating room, and the cover of the unit must be fixed.
Do not open the cover voluntarily because high voltage within the unit may cause electric shock.
When equipment is placed too close or if ventilation is not properly done, system may not work properly, and
maintenance of the system may be difficult.
In order to prevent system failure and to reduce system shut-down by outside environmental factors, air
circulation in the system operating room, and the cover of the unit must be fixed.
Do not open the cover voluntarily because high voltage within the unit may cause electric shock.
PHYSICAL & ENVIRONMENTAL
Operating Temperature : 0°C ~ 40°C
Maintenance Temperature : -20°C~60°C
Operating Humidity : 20%~85% RH
Maintenance Humidity : 20%~90%RH
Maintenance Temperature : -20°C~60°C
Operating Humidity : 20%~85% RH
Maintenance Humidity : 20%~90%RH
Power Supply : DC 12V, 1A (
)
Power Consumption : 4W
When system is operated, input voltage range must be within 10% of nominal voltage, and power consent should be
grounded. Heating devices such as hair dryer, iron, refrigerator should not be used together.
For safe power supply, AVR (Automatic Voltage Regulator) is recommended. The connector linked to this equipment
can affect EMI, so it is recommended to coil the CORE-FERRITE for use.
grounded. Heating devices such as hair dryer, iron, refrigerator should not be used together.
For safe power supply, AVR (Automatic Voltage Regulator) is recommended. The connector linked to this equipment
can affect EMI, so it is recommended to coil the CORE-FERRITE for use.
CAUTIONS FOR INSTALLATION
Be sure to turn the unit off before installing.
Avoid shock or vibration since they may cause unit malfunction.
Keep away from magnets, radio or TV to avoid magnetic damage.
During or after installing the unit, be sure to maintain the area around the unit clean.
Place the unit on a flat surface and maintain temperature properly.
Allow 15 cm of clearance between the rear panel and the wall.
Allow 15 cm of clearance between the rear panel and the wall.
Be careful not to drop any conductive materials into the hole for ventilation.
When replacing built-in fuse, be sure to turn the power off, and unplug the unit.
Avoid locating the unit where direct sunlight will fall, and maintain it cool.
Keep tools and equipment away from people so that they would not be hurt.
Keep tools and equipment away from people so that they would not be hurt.
If ignoring smoke or smell while using the unit, fire or electric shock may occur. In this case, turn the power switch off
immediately, and consult professionals in the closest service center.
immediately, and consult professionals in the closest service center.
Be sure to check dangers, which may occur due to damped floor, ungrounded power extension cable, worn
power cord or lack of safety grounding.
power cord or lack of safety grounding.
When cleaning this unit, be sure to wipe with a dried cloth. If the unit is heavily contaminated, wipe it with a soft
cloth dampened with a mild detergent solution, then wipe dry with a soft clean cloth.
Do not use chemicals such as alcohol, benzene, or thinner because a chemical reaction could result permanent
damaging of the cabinet surface.
cloth dampened with a mild detergent solution, then wipe dry with a soft clean cloth.
Do not use chemicals such as alcohol, benzene, or thinner because a chemical reaction could result permanent
damaging of the cabinet surface.
•
•
•
•
-
-
-
-
-
-
-
-
-
J
-
-
-
-
-
-
-
-
-
-
J