Samsung RS5000H FSR with Foodshowcase, 25.4 cu. ft. Manuel D’Utilisation
English - 26
2. Tighten the compression nut (
B ) onto the
compression fitting.
Do not over-tighten the compression nut (
Do not over-tighten the compression nut (
B ).
3. Turn the water on and check for any leaks
inside the refrigerator, around the water filter,
and in any connection areas.
If you find water drops or leaks, turn off the
main water supply.
If the leaks are in the connection areas, check
the connections and, if necessary, tighten.
If there are leaks in the refrigerator, check
the water filter and confirm it is in the locked
position.
Turn on the water supply and check for leaks
again.
and in any connection areas.
If you find water drops or leaks, turn off the
main water supply.
If the leaks are in the connection areas, check
the connections and, if necessary, tighten.
If there are leaks in the refrigerator, check
the water filter and confirm it is in the locked
position.
Turn on the water supply and check for leaks
again.
4. Plug in the refrigerator.
5. Flush 3 gallons of water through the filter before
5. Flush 3 gallons of water through the filter before
drinking or using the water from the refrigerator.
(Flush approximately 6 minutes.)
This will clean the water supply system and
remove air from the lines.
(Flush approximately 6 minutes.)
This will clean the water supply system and
remove air from the lines.
To flush, press the Water button, and then press
a large glass or cup against the water dispenser
lever. Fill the glass, empty it into the kitchen sink
after it is filled, and then repeat.
a large glass or cup against the water dispenser
lever. Fill the glass, empty it into the kitchen sink
after it is filled, and then repeat.
Additional flushing may be required in
some households.
some households.
6. Open the refrigerator door and make sure there
are no water leaks coming from the water filter.
• After you turn on the refrigerator, let the
ice maker make ice for 1 to 2 days.
Over that period of time, throw out the
first 1 or 2 buckets of ice the ice maker
makes to ensure all impurities have been
removed from the water line.
Over that period of time, throw out the
first 1 or 2 buckets of ice the ice maker
makes to ensure all impurities have been
removed from the water line.
• Only connect the water line to a drinkable water
source.
• If you have to repair or disassemble the water
line, cut off 1/4“ of the plastic tubing to make
sure you get a snug, leak-free connection.
sure you get a snug, leak-free connection.
• You can test the water line quickly using a
paper cup.
Under normal conditions, the water dispenser
can fill a 5.75 oz. (170 cc) cup in about 10
seconds.
Under normal conditions, the water dispenser
can fill a 5.75 oz. (170 cc) cup in about 10
seconds.
COMPLETING THE SET UP
Now that you have your new refrigerator installed
in place, you are ready to set up and enjoy the
features and functions of the appliance.
By completing the following steps, your refrigerator
should be fully operational.
in place, you are ready to set up and enjoy the
features and functions of the appliance.
By completing the following steps, your refrigerator
should be fully operational.
1. Make sure your refrigerator is in an appropriate
location with reasonable clearance between it
and the wall. Refer to installation instructions in
this manual.
and the wall. Refer to installation instructions in
this manual.
2. Once the refrigerator is plugged in, make sure
the interior light comes on when you open the
doors.
doors.
3. Set the Temperature control to the coldest
temperature and wait for an hour.
The freezer will get slightly chilled and the motor
will run smoothly.
Reset the refrigerator and freezer to the
temperatures you want.
The freezer will get slightly chilled and the motor
will run smoothly.
Reset the refrigerator and freezer to the
temperatures you want.
4. After you plug the refrigerator in, it will
take a few hours to reach the appropriate
temperature.
You can store food and drinks in the refrigerator
after the temperature is sufficiently cool.
temperature.
You can store food and drinks in the refrigerator
after the temperature is sufficiently cool.
If condensation or water drops appear
on both sides of the fridge door’s central
part, turn the Energy Saver mode off after
removing the condensation.
(See the explanation of the Energy Saver
button in “Using the Control Panel” on
page 27.)
on both sides of the fridge door’s central
part, turn the Energy Saver mode off after
removing the condensation.
(See the explanation of the Energy Saver
button in “Using the Control Panel” on
page 27.)
Preventing Power Cord Damage
To prevent power cord damage, fix any excess
power cord to the top rear of the refrigerator as
shown in the illustration below.
power cord to the top rear of the refrigerator as
shown in the illustration below.
SSEDA FSR-1 EN-���.indd 26
14. 11. 28. �� 1:11