Samsung No Dispenser French Door Guide D’Installation Rapide

ENGLISH

•   Allow  your  refrigerator  to  operate  and 

cool down for 24 hours (1 full day) be -
fore the ice maker starts producing ice.

•   

-

pacity, dispense a few cubes 8 and 16 
hours after installation.

•   If 

ICE OFF is lit, the ice maker will not make ice.

• To activate the ice maker, press the 

ICE OFF 

but-ton on the control panel so it is no lon -
ger lit.

•   When installing, servicing or cleaning behind the 

refrigerator, be sure of the following:

•   

refrigerator, cut a large section of the cardboard 
carton and place under the refrigerator where 
you are working.

•   Pull the unit straight out and push back in 

 

k

c

e

h

C

 

 •

if the ice bucket is completely 

inserted. (On some models)

•   Freezer  temp  may  not  be  enough; 

set it to -2ºF(-19ºC) or lower.

•   

cubes may be produced.

•   

After installation or when replacing the 

 

1 gallon (2~3minutes) of water to 

remove trapped air from the water line.   

Otherwise, water may drip after dis -

pensing water. (On some models)

•   

because the stored water in the water valve has 
not cooled completely. Dispense several glasses 
of water and then it would be cool.

 

e

h

T 

 .

1

Water Line must be fully Inserted to the center 

of transparent coupler to prevent water leakage 
from the dispenser.

•   These  noises  may  be  heard  occasionally  inside 

the refrigerator. This is normal. This sound occurs 
when  various  items  contract  or  expand  while 
temperatures  are  changing;  especially  during 
defrosting. This may also occur when electronic 
devices including the ice maker are operating.

•   You can select your Pantry 

temperature from among the     
following.

Wine Party Dishes (38°F[3°C])
Fresh (38°F[3°C])
Chilled (34°F[1°C])
Deli (41°F[5°C])

•   

control lever, turn it clockwise or counter-clock -
wise to level the door.

•

•

•

properly, air could penetrate into the water line 
causing water dripping from the water dispenser.

•   

CAUTION : Insert the water line into the coupler com -
pletely and slide in the clip at the end of the coupler.

Red Clip 

(1/4")

Dispenser 
Door Tube

Cabinet 
Tube

DA99-04014A  Rev 04 

•   

clockwise so it is aligned with the 

printing  mark  on  the  cover,  lock -

-

ter printing as illustrated.

•

 

e

h

t 

g

n

it

r

e

s

n

i 

f

o

 

e

l

b

u

o

r

t 

n

i 

e

r

a

 

u

o

y

 f

I 

 

water supply valve. For details, refer to the “Chan -

 

r

e

f

e

r 

,

s

li

a

t

e

d

 

r

o

F 

 

to the user manual “Adjusting the level”

•   Recommended Temp Settings : 0ºF(-18ºC) for 

freezer and 37ºF (3ºC) for refrigerator.

•   

use water about 300 gallons (6 month) Reset the indi -

the "

Ice Type/Water/Hold 3 sec for Filter Reset" 

button for 3 seconds.

•   Ice    :  Press  the  “

” button  to  turn  the  ice 

making function o .

The display may di er depending on models.
For details, refer to the user manual “Using the control 
panel.

PUSH

Control Lever

Flat-blade screw driver(-)

<sample>

• Allow  your refrigerator to operate and cool down for 

24 hours (1 full day) to reach to the set temperature.

 t

u

p

 

u

o

y

 

n

e

h

w

 ,

o

s

l

A

 

 •

room temperature or warmer 

food into your refrigerator, it may need an additional 
24 hours for the fridge to reach the set temperature.

•  Wipe o  the condensation with a dry towel (This 

may occur during hot and humid seasons.)

• If the condensation occurs on the doors, turn off

 

the Energy Saving function.

f 

s

r

o

o

d

 

e

h

t 

n

e

p

o

 

u

o

y

 f

I 

 •

requently or for too long, it 

may cause moisture inside the fridge.

• If food with too much moisturere is stored near the 

cooling vents, it may get frozen. Be sure to keep 
moist food away from the cooling vents.

DA99-04014A(EN+FR+ES)-0.3.indd   1

2012.4.2   1:55:39 PM

If the water line is not inserted into the coupler

2. Insert the clip in the install pack and check that it

Pull out the freezer drawer       , then you can
see the lower hinge      .

Adjust the height by turning a philips 
screwdriver (+)       clockwise (         ) or 
counterclockwise (         ).

1

2

3

4

Insert a philips screwdriver (+)       into the shaft
      of the lower hinge.

DOWN

UP

3

1

2

3

4

3

•

•