Samsung Front Load Washer With VRT Guide De Montage

Remove all shipping bolts at the 

back of washer with supplied 

spanner. (Except for WF45H6*, 

WF45K* model)

Hold the shipping bolt with your 

hand and pull it through the 

wide section of the hole. Repeat 

for each shipping bolt.

Fill the holes with the supplied 

bolt hole covers.



Level the washer by turning the leveling wheel 

clockwise or counter clockwise to the required level 

with the supplied wrench. (Except for WF45H6*, 

WF45K* model)

Check whether washer shakes and level 

again, if necessary.

When your washer is leveled, tighten 

the locking nuts using the wrench or (-) 

flathead screwdriver.



1. Check the installation location. 

    □ CHECK : The floor must be sturdy. (Carpet and soft tile surfaces are not permitted.

2. And move the washer to the installation location.

□

 Washer plugged in, power OK

□

 No water leakage

□

 Water hose connected properly

□

 Drain hose connected properly

□

 No vibration / noise

□

 Washer leveled

□

 Shipping bolts removed

Carpenter’s 

level

Pliers

Tape measure

Hose guide

Anti-slip pads

Water supply hoses

Bolt hole covers

Type1

Type2

Tie strap 

(option)

Wrench

(Except for 

WF45H6*,WF45K* model)

Flat screwdrilver

Connect one end of the COLD/

HOT water supply hoses to the 

each COLD/HOT water supply 

intakes at the back of the washer.

Tighten Coupling by hand until 

it is snug.

Then tighten two-thirds of a turn 

with pliers.

For proper operation, make sure 

both Hot & Cold hoses from faucets 

are connected to the corresponding 

Hot / Cold water inlets on the washer.



COLD (Left)

Water

HOT (Right)

Water

To keep the drain hose spout 

bent, use the supplied plastic 

hose guide.

The drain hose must be placed 

at a height between 23.6 in 

(60cm) and 35.4 in (90cm).

Laundry tub must be no shorter 

than 18 in (46 cm) and no longer 

than 96 in (245 cm).

Drain hose

Hose guide

96” Max

18” Min

Tie strap

Tie strap

Hose 

retainer

96” Max

18” Min

8” Max

6” Min

Hose 

retainer

Confirm whether washer is well seated and does not shake. Adjust 

leveling legs, if necessary.

Your washer must be leveled on all four sides. Use a carpenter’s level 

on all four corners of your washer to ensure it’s level.

Make sure a Rubber washer is 

inside each coupling on both ends.

Tighten Coupling by hand until 

it is snug.

Then tighten two-thirds of a turn 

with pliers.

Run water in a bowl or basin to get 

rid of any debris inside hose. Check 

for HOT and Cold water supply.



Rubber

washer

Coupling

Rubber washer

French on back 

Spanish on back 

1. Powering your washing machine.

2. Run a test cycle(Rinse+Spin) with small  amount of laundry such as 4~5 Towels.

(1)  Check for any leakage at the hose connections. 



 If water leaks while water is being supplied or drained, check the water connections. (Refer to Step 4,5,6) 

(2)  Check for vibration and noise.

 



 If the washer rocks and vibrates excessively, level your washer again. (Refer to Step 7,8)

1.  Completely clean the bottoms of the adjustable legs and wipe away any dust and oil.

2.  Mark the locations of the adjustable front legs of the washing machine where the anti-slip 

pads should be installed.

3.  Attach the anti-slip pad by tilting or moving the washing machine. When you attach the pad, 

remove the plastic film from the pad and attach the sticker side of the pad to the floor so 

that the rough side is facing upward. You should not attach the sticker side of the pad to an 

adjustable leg.

4.  After installing the washing machine and anti-slip pad, check if the adjustable legs are level 

again. 

Rough side
Sticker

DC68-02580C-11

When unpacking the washing machine,a 

collaboration of two persons is required. Do not lay 

the machine on its front face when removing the 

bottom cushion.
* Models that do not feature handles:

Remove the top cushion from the washing machine 

and put the top cushion (or its equivalent) on the 

floor. Lay the washing machine on the top cushion 

and then remove the bottom cushion.



Models with handles

*Models without handles

* To order, please refer to call center number 

on the back page of your "User Manual"

lf applicable

(Except for WF36J4*,WF45K*,  WF50K* 

model)

Installation Guide-02580C-11_EnCfrMes.indd   1

2016/1/11   17:08:39