Samsung RF260BEAESP Manuel D’Utilisation
14_
setting up
Slip the compression nut through the supplied
1.
plastic tubing .
Tighten the compression nut
Tighten the compression nut
2.
onto the
6.35 mm compression fi tting.
If you are using copper tubing, slip the
If you are using copper tubing, slip the
-
compression nut (not included) and ferrule
(not included) on copper tubing (not included)
as shown.
If you are using plastic tubing
(not included) on copper tubing (not included)
as shown.
If you are using plastic tubing
-
, insert the
molded end(Bulb) of the plastic tubing into
the compression fi tting.
Do not use without the molded end(Bulb) of
the plastic tubing .
Tighten the compression nut
the compression fi tting.
Do not use without the molded end(Bulb) of
the plastic tubing .
Tighten the compression nut
3.
onto the
compression fi tting. Do not over-tighten the
compression nut .
Turn water on and check for any leakage.
compression nut .
Turn water on and check for any leakage.
4.
Only connect the water line to a drinkable
water source.
water source.
If you have to repair or disassemble the water line,
cut off 6 mm of the plastic tubing to make sure
you get a snug, leak-free connection.
cut off 6 mm of the plastic tubing to make sure
you get a snug, leak-free connection.
CAUTION
COMPLETING THE SET UP
Now that you have your new refrigerator installed
in place, you are ready to set up and enjoy the
features and functions of the appliance.
By completing the following steps, your refrigerator
should be fully operational.
in place, you are ready to set up and enjoy the
features and functions of the appliance.
By completing the following steps, your refrigerator
should be fully operational.
Make sure your refrigerator is in an appropriate
1.
location with reasonable clearance between it
and the wall. Refer to installation instructions in
this manual.
Once the refrigerator is plugged in, make sure
and the wall. Refer to installation instructions in
this manual.
Once the refrigerator is plugged in, make sure
2.
the interior light comes on when you open the
doors.
Set the Temperature control to the coldest
doors.
Set the Temperature control to the coldest
3.
temperature and wait for an hour. The freezer
will get slightly chilled and the motor will run
smoothly. Reset the refrigerator and freezer to
the temperatures you want.
After you plug the refrigerator in, it will
will get slightly chilled and the motor will run
smoothly. Reset the refrigerator and freezer to
the temperatures you want.
After you plug the refrigerator in, it will
4.
take a few hours to reach the appropriate
temperature. You can store food and drinks
in the refrigerator after the temperature is
suffi ciently cool.
temperature. You can store food and drinks
in the refrigerator after the temperature is
suffi ciently cool.
To get more space , you can remove top freezer
drawers since it does not affect thermal and
mechanical characteristics. A declared storage
volume of frozen food storage compartment is
calculated with these drawers removed.
drawers since it does not affect thermal and
mechanical characteristics. A declared storage
volume of frozen food storage compartment is
calculated with these drawers removed.
Plastic tubing
(Supplied)
Ferrule
(Not supplied)
Compression nut
(6.35 mm) (Supplied)
(6.35 mm) (Supplied)
Compression fi tting
(Supplied)
(Supplied)
Bulb
Compression nut
(6.35 mm)
(Not supplied)
(6.35 mm)
(Not supplied)
Copper tubing
or
Plastic tubing
(Not supplied)
(Not supplied)
Household water line
Refrigerator
Refrigerator
DA68-02616B(0.0).indb 14
DA68-02616B(0.0).indb 14
2012.6.15 7:47:55 PM
2012.6.15 7:47:55 PM