Audiovox vme 8013 Manuel D’Utilisation
Introduction
Congratulations on your purchase of the Audiovox VME 8013 Mobile Multimedia Receiver. It’s a good idea to read all of the instructions before
beginning the installation. We recommend having your Audiovox VME 8013 installed by a reputable installation shop.
beginning the installation. We recommend having your Audiovox VME 8013 installed by a reputable installation shop.
Installation
This unit is designed for installation in cars, trucks and vans with an existing radio opening. In many cases, a special installation kit will be required
to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialty shops. Always check the kit
application before purchasing to make sure the kit works with your vehicle.
This unit is designed for installation in cars, trucks and vans with an existing radio opening. In many cases, a special installation kit will be required
to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialty shops. Always check the kit
application before purchasing to make sure the kit works with your vehicle.
Tools and Supplies
The following tools and supplies are needed to install the radio:
The following tools and supplies are needed to install the radio:
• Torx type, flathead and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16-18 gauge speaker wire
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16-18 gauge speaker wire
Preparation
Disconnect Battery
Before you begin, always disconnect the battery negative terminal.
NOTE:
If the VME 8013 is to be installed in a car equipped with an onboard
drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost.
Under these conditions, use extra caution during installation to avoid causing a short circuit.
If the VME 8013 is to be installed in a car equipped with an onboard
drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost.
Under these conditions, use extra caution during installation to avoid causing a short circuit.
Remove Radio from Sleeve
Lift latches on both sides of sleeve to remove half-sleeve from radio.
Lift latches on both sides of sleeve to remove half-sleeve from radio.
Mounting Sleeve Installation
1. Slide the mounting sleeve off the chassis. If it is locked into position,
use the removal tools (supplied) to disengage it.
1. Slide the mounting sleeve off the chassis. If it is locked into position,
use the removal tools (supplied) to disengage it.
2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is too small, carefully cut or file as necessary until the
sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check for sufficient space behind
the dashboard for the radio chassis.
sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check for sufficient space behind
the dashboard for the radio chassis.
3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard
opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard.
opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard.
CAUTION: For proper operation of the DVD player, the chassis must be mounted within 20° of horizontal. Make sure the unit is mounted
within this limitation.
within this limitation.
4. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully
and make certain all connections are secure and insulated with wire nuts or electrical tape. See “Wiring” on page 5. After completing the wiring
connections, turn the unit on to confirm operation (vehicle ignition must be on). If the unit does not operate, re-check all wiring until the problem is
corrected.
and make certain all connections are secure and insulated with wire nuts or electrical tape. See “Wiring” on page 5. After completing the wiring
connections, turn the unit on to confirm operation (vehicle ignition must be on). If the unit does not operate, re-check all wiring until the problem is
corrected.
5. Make sure the radio is right-side up, then carefully slide the radio into the mounting sleeve until it is fully seated and the spring clips
lock it into place.
lock it into place.
3
Subject to technical changes