Sony HTCT260H Manuel D’Utilisation
21
GB
BLUET
O
O
T
H Function
Sound may be interrupted because of a
problem with the BLUETOOTH device.
problem with the BLUETOOTH device.
Once a pairing operation is performed,
it does not have to be performed again.
However, you must repeat pairing in the
cases listed below.
Pairing information is deleted by
it does not have to be performed again.
However, you must repeat pairing in the
cases listed below.
Pairing information is deleted by
repairing the system.
Pairing for 9 or more devices is to be
set.
This system can set pairing with up to
8 devices. If pairing is to be set on a
device after pairing has been set on
8 devices, the pairing information on
a device whose connection date is the
oldest is overwritten with new
information.
This system can set pairing with up to
8 devices. If pairing is to be set on a
device after pairing has been set on
8 devices, the pairing information on
a device whose connection date is the
oldest is overwritten with new
information.
The connection history with this
system is deleted on the connected
device.
device.
The system is reset to default.
If you intend to pair the system with 2
or more BLUETOOTH devices, manual
pairing is necessary.
or more BLUETOOTH devices, manual
pairing is necessary.
1
Place the BLUETOOTH device to
be connected to this system
within 1 meter of the system.
be connected to this system
within 1 meter of the system.
2
Press PAIRING on the remote
control, or press the
control, or press the
(BLUETOOTH) key on the
Sound Bar for more than
2 seconds.
2 seconds.
3
Perform steps 3 to 6 in “Pairing
automatically” (page 20).
automatically” (page 20).
“Passkey” may be called “Passcode,”
“PIN code,” “PIN number” or
“Password,” etc., depending on the
device.
“PIN code,” “PIN number” or
“Password,” etc., depending on the
device.
The pairing standby status of the
system is canceled after about 1 minute.
If pairing is not successful, redo the
procedure from step 1.
system is canceled after about 1 minute.
If pairing is not successful, redo the
procedure from step 1.
If you wish to pair with several
BLUETOOTH devices, perform the
procedure from steps 1 to 3 individually
for each BLUETOOTH device.
BLUETOOTH devices, perform the
procedure from steps 1 to 3 individually
for each BLUETOOTH device.
If no pairing information is stored in the
system, the system automatically
enters pairing mode when “BT AU” is
selected as input. In this case, pairing
mode is not released automatically.
system, the system automatically
enters pairing mode when “BT AU” is
selected as input. In this case, pairing
mode is not released automatically.
You can listen to a music that supports
SCMS-T content protection.
Before starting music playback, check
the following:
SCMS-T content protection.
Before starting music playback, check
the following:
The BLUETOOTH function on the
BLUETOOTH device is on.
BLUETOOTH device is on.
The pairing procedure is completed
on both this system and the
BLUETOOTH device.
on both this system and the
BLUETOOTH device.
1
Press
+/ to select “BT AU.”
2
Start the BLUETOOTH
connection from the
BLUETOOTH device.
The (BLUETOOTH)
connection from the
BLUETOOTH device.
The (BLUETOOTH)
indicator
lights up in blue when the
BLUETOOTH connection is
established.
BLUETOOTH connection is
established.
3
Start playback on the
BLUETOOTH device.
For details on operation, see “To
control a BLUETOOTH device”
(page 11).
BLUETOOTH device.
For details on operation, see “To
control a BLUETOOTH device”
(page 11).
4
Adjust the volume.
Set the volume of the BLUETOOTH
device to a moderate level and
press
Set the volume of the BLUETOOTH
device to a moderate level and
press
+/.
Pairing manually
Notes
Listening to music with the
BLUETOOTH connection
BLUETOOTH connection
continued