Sony LPR-1000MD Manuel D’Utilisation

Mi
sc
el

la

ne
ou
s

Error Messages

56

a) xx means the last alphabetic characters of the 

message. These indicates the color and location of 
the ink.  For detailed information, see “Replacing 
the Ink Cartridges” on page 43.

When the paper jams, the error message “Paper jam” 
appears on the printer window display. Remove the 
jammed paper following the steps below.

When you put your hands inside of the printer, be careful 
not to hurt yourself by touching hot or sharp parts.

Push the READY button on the printer. The jammed 
paper is ejected automatically.
When the jammed paper is not ejected and the message 
“Paper jam” does not disappear on the printer window 
display even though you push the READY button, 
proceed as follows to remove the jammed paper.

Ink depleted xx 

a)

(xx ink has run out.)
(xx ink cartridge is not 
attached.)

• The amount of ink is low.

tReplace the ink cartridge. 

• The ink cartridge is not set 

correctly.
tCheck and set the ink cartridge, 

if necessary. (page 43)

• The head cartridge is not set 

correctly.
tCheck and set the head 

cartridge, if necessary. (Refer 
to “Attaching the Head 
Cartridge” described in the 
printed Setup Manual.)

Cooling down

The temperature of the head or of the 
inside of the printer rises.
tThis is not a malfunction. Wait for 

a while. If the room temperature is 
high, the printer may run hot. Be 
careful about the room 
temperature.

Head cartridge/is not 
attached
(The print head 
cartridge is not 
attached.)

The head cartridge is not attached 
correctly.
tConfirm whether the head 

cartridge is attached correctly. 
(Refer to “Attaching the Head 
Cartridge” described in the printed 
Setup Manual.)

Head cover/is open
(The print head cover is 
open.)

• The head cover is open.

tClose the cover firmly.

• The head cartridge lock screws are 

not tightened securely.
tCheck them and tighten them 

securely. (Refer to “Attaching 
the Head Cartridge” described 
in the printed Setup Manual.)

• The harness of the head cartridge 

cable is not pushed in to the 
groove securely.
tPush the harness of the head 

cartridge cable into the groove 
securely. (Refer to “Attaching 
the Head Cartridge” described 
in the printed Setup Manual.)

Main cover/is open
(The main cover is 
open.)

The main cover is not closed.
tClose the main cover until both 

left and right eject buttons click 
and lock.

Cleaning unit/is not 
attached.

The head cleaning unit is not 
attached.
tAttach the head cleaning cartridge. 

(Refer to “Attaching the Head 
Cartridge” described in the printed 
Setup Manual.)

Cleaning unit/is not 
closed.

The head cleaning unit is not inserted 
securely.
tOpen the main cover by pushing 

both left and right eject buttons 
and push the head cleaning unit 
until it is seated properly. (Refer to 
“Attaching the Head Cleaning 
Unit” described in the printed 
Setup Manual.) 

A print data error/has 
occurred.
(Print data error.)

Print data error occurs.
Remove the print data error.
tCancel the print job when the print 

data is left in the spooler. 
(page 23)

tPush the READY button.
tIf the printer does not recover even 

when you push the READY 
button, push and hold the ON/
STANDBY button for about three 
seconds so that the printer is in 
standby mode. Then push the ON/
STANDBY button again so that 
the printer is set to on. If the 
printer does not recover even after 
you push the ON/STANDBY 
button, set the main power switch 
located on the back of the printer 
to the off side, and then turn the 
printer on again.

Malfunction/xxx

The printer is in need of repairment. 
Consult your dealer. xxx indicates the 
error code. If you write the code on 
the status column of “Customer 
Confirmation Sheet,” the service 
personal understand the nature of the 
problem.