Sony rdr-gx700 Manuel D’Utilisation
20
Controlling TVs with the remote
You can adjust the remote’s signal to control your
TV.
If you connected the recorder to an AV amplifier
(receiver), you can use the supplied remote to
control the AV amplifier’s (receiver’s) volume.
TV.
If you connected the recorder to an AV amplifier
(receiver), you can use the supplied remote to
control the AV amplifier’s (receiver’s) volume.
Notes
• Depending on the connected unit, you may not be able
to control your TV or AV amplifier (receiver) with
some or all of the buttons below.
some or all of the buttons below.
• If you enter a new code number, the code number
previously entered will be erased.
• When you replace the batteries of the remote, the code
number may be reset to the default setting. Set the
appropriate code number again.
appropriate code number again.
1
Slide the TV/DVD switch to TV.
2
Hold down [/1.
3
Enter your TV’s manufacturer code (see
“Code numbers of controllable TVs”
below) using the number buttons.
“Code numbers of controllable TVs”
below) using the number buttons.
4
Release [/1.
When the TV/DVD switch is set to TV, the
remote performs the following:
remote performs the following:
* If you use the number buttons to select the TV’s
programme position, press -/-- followed by the number
buttons for two-digit numbers.
buttons for two-digit numbers.
To operate the TV/DVD button
(for SCART connections only)
(for SCART connections only)
The TV/DVD button switches between the
recorder and the last input source selected on the
TV. Point your remote at the recorder when using
this button. The button works even if the TV/DVD
switch is set to DVD.
When you connect the recorder to the TV via the
SCART jacks, the input source for the TV is set to
the recorder automatically when you start
playback. To watch another source, press the TV/
DVD button to switch the TV’s input source.
recorder and the last input source selected on the
TV. Point your remote at the recorder when using
this button. The button works even if the TV/DVD
switch is set to DVD.
When you connect the recorder to the TV via the
SCART jacks, the input source for the TV is set to
the recorder automatically when you start
playback. To watch another source, press the TV/
DVD button to switch the TV’s input source.
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the one
that works with your TV.
entering them one at a time until you find the one
that works with your TV.
[/1
Turns your TV on or off
2 (volume) +/–
Adjusts the volume of your
TV
TV
PROG +/–
Selects the programme
position on your TV
position on your TV
(wide mode)
Switches to or from the
wide mode of a Sony wide-
screen TV
wide mode of a Sony wide-
screen TV
t
(TV/video)
Switches your TV’s input
source
source
1
2
3
4
5
6
7
8
9
0
TV/DVD
switch
switch
"
/
1
2
+/–
Number buttons,
SET/-/--
SET/-/--
t
, TV/DVD
PROG +/–
Number buttons and
SET, -/--*
SET, -/--*
Selects the programme
position on your TV
position on your TV
Manufacturer
Code number
Sony
01 (default)
Aiwa
01 (default)
Grundig
11
Hitachi
23, 24, 72
Loewe
06, 45
Nokia
15, 16, 69, 73
Panasonic
17, 49
Philips
06, 07, 08, 23, 45, 72
Saba
12, 13, 36, 43, 74, 75
Samsung
06, 22, 23, 71, 72
Sanyo
25
Sharp
29
Telefunken
12, 13, 36, 43, 74, 75
Thomson
12, 13, 43, 74, 75
Toshiba
38
LG
06
JVC
33