Sony SPP-N1003 Manuel D’Utilisation

When you hear the phone ring;
• Press 

(TALK) (or any key except (OFF)).

or

• Pick up the handset from the base unit when the handset is placed on 

the base unit.

The TALK/BATT LOW lamp lights up.

When you’re done talking, replace the handset on the base unit or press 

(OFF).
The TALK/BATT LOW lamp goes off.

• Do not cover the microphone during the conversation; otherwise, the other party cannot hear 

your voice.

• If you hear beeps during the conversation, move closer to the base unit; otherwise, the call will 

be disconnected after 15 seconds. Note that, however, you may not hear beeps if it’s noisy on 
the handset.

When you press 

(TALK), the handset automatically searches for the channel with the 

best reception. However, if you notice interference during a conversation, move 
closer to the base unit.
If interference persists, press 

(CHANNEL/RINGER) to switch to another channel to 

improve the sound quality of your telephone conversation.

If you hear five short beeps when you press 

(CHANNEL/RINGER), move closer to the base unit.

The handset will beep every three seconds with the TALK/BATT LOW lamp 
flashing at the same time. Finish your call and charge the battery pack.

If this occurs, you cannot use the handset without charging it for more than one minutes.

Press 

(TALK), and wait until the TALK/BATT LOW lamp lights up.

Press 

(REDIAL/PAUSE) to redial the number last dialed.

If the number exceeds 32 digits, the beeps will alert you that the number cannot be dialed.

Press 

(REDIAL/PAUSE) twice.

The number will be erased from the memory, and you’ll hear a long confirmation 
beep.

You can dial with a touch of a few keys by storing a phone number on a dialing key.

Do not allow more than 20 seconds to elapse between each step of the procedure.

• If you enter a wrong number, press 

(PGM), then start from the beginning.

• Affix the supplied directory to a desired place.

Before entering a phone number in step 4, do as follows:

Enter the outside line access digit (e.g., 9).

Press 

(REDIAL/PAUSE).

Store a new number, as described previously.

You can replace the stored number with a new number, but you cannot just erase it.

Press 

(TALK) and wait until the TALK/BATT LOW lamp lights up.

The dialing keys light up.

Press 

(SPEED DIAL).

Enter the desired speed dialing number (

(0) to (9)).

The phone number stored in the speed dialing number will be dialed.

You can page the handset from the base unit. Note that you cannot page if the handset 
is in use.

Attach the telephone line cord and AC power adaptor cord to the base 
unit. Bundle the loose telephone line cord or AC power adaptor cord, if 
necessary.

Plug the telephone line cord into the telephone outlet, and hook the base 
unit to the wall plate as illustrated. Plug the AC power adaptor to an AC 
outlet. Then raise the antenna so that it points towards the ceiling.

Pick up the handset from the 
base unit.

Press 

(TALK), and wait until 

the TALK/BATT LOW lamp 
lights up.
The dialing keys light up.
You then hear a dial tone. If 
you hear beeps, move closer to 
the base unit.

Dial the phone number.

When you’re done talking, 
press 

(OFF).

The TALK/BATT LOW lamp 
goes off.

Adjust the handset 
volume

Set the VOL switch to H (high), M (middle) or L (low).

Switch to tone 
dialing temporarily

Press 

(* TONE) after you’re connected.

The line will remain in tone dialing until disconnected.

Set the ringer type

While the handset is not in use, press 

(CHANNEL/RINGER). Each 

press of 

(CHANNEL/RINGER) switches the ringer type by one of 

four type.

Switch to another 
call (“call waiting 
service”*)

* You need to subscribe to the service from your telephone company.

Press 

(FLASH).

Press the button again to get back to the first caller.

(FLASH)

(CHANNEL/RINGER)

(* TONE)

(REDIAL/PAUSE)

Press 

(PGM).

The TALK/BATT LOW lamp 
flashes. 

Press 

(SPEED DIAL).

The dialing keys light up.

Press one of the dialing keys (

(0) 

to 

(9)) to store a phone number on.

You hear a confirmation beep.

Enter the phone number you want 
to store.
You can enter up to 20 digits, 
including a tone and a pause, each 
of which is counted as one digit.

Press 

(PGM).

You hear a long confirmation beep, 
and number is stored. The TALK/
BATT LOW lamp goes off.

Press 

(HANDSET LOCATOR).

The handset rings for about one 
minute.
To end the page, press 

(OFF) on 

the handset.

(REDIAL/PAUSE)

(HANDSET LOCATOR)