Manualsbrain.com
  1. Manuels
  2. Marques
  3. Panasonic
  4. SC-HC28
  5. Manuel D’Utilisation

Panasonic SC-HC28 Manuel D’Utilisation

Télécharger
Page de 16
11
RQT9729
EN
GL
IS
H
Stations cannot be selected.
Change the FM frequency step.
1 Press [RADIO] to select “FM”.
2 Press and hold [RADIO] on the unit.
After a few seconds the display changes to show the 
current lowest frequency. Continue to hold the button 
down. The lowest frequency changes and the step is 
changed.
Cannot charge or operate.
≥ Have you selected the appropriate selector? 
Press [iPod] to select either “IPOD_DOCK” or 
“IPOD_PORT”.
≥ Check that the iPod/iPhone/iPad is connected properly. 
(l 6)
≥ The battery of the iPod/iPhone/iPad is depleted. Charge 
the iPod/iPhone/iPad, and then operate again.
≥ Connect the iPod/iPhone/iPad again or try to restart the 
iPod/iPhone/iPad.
≥ When this unit is in standby mode, charging will not start 
when using the “IPOD_PORT” connection.
Turn this unit on and make sure the charging has started 
before switching this unit to standby mode.
The remote control doesn't work properly.
≥ The remote control and this unit are using a different 
code. (l right, “REMOTE ”)
≥ Is the battery depleted or is the battery inserted 
incorrectly? (l 4)
The following messages or service numbers 
may appear on the unit's display.
“--:--”
≥ You plugged the AC power supply cord in for the first time or 
there was a power failure recently. Set the time (l 9).
“ADJUST CLOCK”
≥ Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
≥ Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”
≥ The unit has been left unused for about 30 minutes and will 
shut down within a minute. Press any button to cancel it.
“CHECKING CONNECTION”
≥ The unit is checking the connected iPod/iPhone/iPad. 
≥ If this display keeps appearing, make sure that the battery of 
the iPod/iPhone/iPad is not depleted and that the iPod/
iPhone/iPad is turned on and connected correctly (l 6).
“DIMMER”
≥ Appears 10 seconds after the volume is turned to “0”.
“DOCK OPEN”
≥ Is the dock open? Close the dock completely to open the 
sliding door.
“ERROR”
≥ Incorrect operation is performed. Read the instructions and 
try again.
“F
” (“   ” stands for a number.)
≥ There is a problem with this unit.
Note down the displayed number, disconnect the AC power 
supply cord and consult your dealer.
“ILLEGAL OPEN”
≥ Sliding door is not in correct position. Turn the unit off and on 
again. If this display appears again, consult the dealer.
“IPOD_DOCK OVER CURRENT ERROR”
“IPOD_PORT OVER CURRENT ERROR”
≥ The iPod/iPhone/iPad is drawing too much power. 
Disconnect the iPod/iPhone/iPad and turn the unit off and on 
again.
“NODEVICE”
≥ The iPod/iPhone/iPad device is not inserted correctly. Read 
the instructions and try again (l 6).
≥ The battery of the iPod/iPhone/iPad is depleted. Charge the 
iPod/iPhone/iPad and turn it on before connecting.
“NO DISC”
≥ Insert a disc to be played (
l 6).
“NO PLAY”
≥ A CD that is not in CD-DA format is inserted. It cannot be 
played.
“NOT SUPPORTED”
≥ You have connected an iPod/iPhone/iPad that cannot be 
played (l 13).
≥ If the iPod/iPhone/iPad is compatible, turn it on and connect 
it correctly.
“READING”
≥ The unit is checking the CD information. After this display 
has disappeared, start operating.
“REMOTE ” (“   ” stands for a number.)
≥ The remote control and this unit are using different codes. 
Change the code on the remote control.
– When “REMOTE 1” is displayed, press and hold [OK] and 
[RADIO] for more than 4 seconds.
– When “REMOTE 2” is displayed, press and hold [OK] and 
[CD] for more than 4 seconds.
iPod/iPhone/iPad operations
Remote control
Messages
SC-HC28~RQT9729.book  Page 11  Friday, December 28, 2012  4:05 PM