Toshiba 32a62 Manuel D’Utilisation
13
W
elcome to
Toshiba
Connecting
y
our T
V
Using the
Remote Contr
ol
Setting up
y
our T
V
Using the T
V’s
F
eatur
es
Appendix
Index
VCR code table
Brand
Code
Adventura
019
Aiko
297
Aiwa
019
Akai
060, 068, 080, 125,
261
261
American High
054
Asha
259
Audiovox
056
Beaumark
259
Bell & Howell
123
Brandt
206
Broksonic
140, 203, 230, 314,
380
380
Calix
056
Canon
054
Capehart
039
Carver
100
CCE
091, 297
Citizen
056, 297
Colt
091
Craig
056, 066, 091, 259
Curtis Mathes
054, 060, 079
Cybernex
259
Daewoo
039, 064, 297
Daytron
039
Dynatech
019
Electrohome
056
Electrophonic
056
Emerex
051
Emerson
019, 021, 056, 062,
080, 087, 140, 203,
227, 228, 230, 231,
297, 313, 314, 380,
498
080, 087, 140, 203,
227, 228, 230, 231,
297, 313, 314, 380,
498
Fisher
066, 073, 085, 123
Fuji
052, 054
Funai
019, 344
Garrard
019, 344
GE
054, 079, 084, 221
Go Video
251, 298
Goldstar
037, 056, 057
Gradiente
019
Harley Davidson
019
Harman/Kardon
057, 094
Harwood
087, 091
Headquarter
065
HI-Q
066
Hitachi
060, 061, 084, 124,
185, 254
185, 254
Jensen
060
JVC
027, 060, 086
Kenwood
057, 060, 086
Note:
•
•
Every time you replace the batteries, you
must reprogram the remote control.
must reprogram the remote control.
•
Some newer VCRs are capable of working
on either of two remote codes. These
VCRs have a switch labeled “VCR1/
VCR2.” If your VCR has this kind of switch
and does not respond to any of the codes
for your VCR brand, set the switch to the
other position (VCR1 or VCR2) and
reprogram the remote control.
on either of two remote codes. These
VCRs have a switch labeled “VCR1/
VCR2.” If your VCR has this kind of switch
and does not respond to any of the codes
for your VCR brand, set the switch to the
other position (VCR1 or VCR2) and
reprogram the remote control.
CH RTN
ADV/
PIP CH
LIGHT
MUTE TV/VIDEO TIMER
RECALL POWER
TV
CABLE
VCR
ENT
C.CAPT
MENU
1
4
2
5
3
6
7
8
9
0
100
Channel
Numbers
Numbers
TV/CABLE/VCR
switch
switch
ENT (used for the “ENTER”
command with some VCRs
and cable TV converters)
command with some VCRs
and cable TV converters)
POWER
CH
CH (Channel)
VOL
RECALL
Programming the remote control for use
with a non-Toshiba VCR or cable TV converter
with a non-Toshiba VCR or cable TV converter
The remote control provided with your Toshiba TV is
preprogrammed to operate Toshiba VCRs and cable TV converters.
To operate a non-Toshiba VCR or converter using the TV remote
control, program the remote control (see below) and then see “Using
the remote control with a VCR or cable TV converter” on page 12.
preprogrammed to operate Toshiba VCRs and cable TV converters.
To operate a non-Toshiba VCR or converter using the TV remote
control, program the remote control (see below) and then see “Using
the remote control with a VCR or cable TV converter” on page 12.
To program the remote control:
1. Refer to the VCR and cable TV converter code tables (below
and on the next page) to find the corresponding code for your
VCR or converter brand.
If more than one code is listed, try each one separately until you
find the one that works.
VCR or converter brand.
If more than one code is listed, try each one separately until you
find the one that works.
2. If you are programming the remote control to operate your:
• VCR: Set the TV/CABLE/VCR switch on the remote control
to “VCR.”
• Cable TV converter: Set the TV/CABLE/VCR switch on the
remote control to “CABLE.”
3. While holding down RECALL, press the CHANNEL
NUMBERS
to enter the three-digit code for your VCR or
cable TV converter brand.
4. Point the remote control at the VCR or converter, and press
POWER
to test the code.
• If the VCR or converter responds, you entered the correct
code.
• If the VCR or converter does not respond, repeat steps 1–4
using another code.
5. Set the TV/CABLE/VCR switch to “TV” to control the TV.
For future reference, write down the codes you used:
VCR code: _____________________
Cable TV converter code: _____________________