Toshiba theaterview 50h72 Manuel D’Utilisation
Intr
oduction
Connecting
y
our T
V
Using the
Remote Contr
ol
Setting up
y
our T
V
Using the T
V’s
F
eatur
es
Appendix
Index
15
1
2
3
4
5
6
7
8
9
ENT
100
0
CH
VOL
POWER
TIMER
RECALL
TV/VIDEO
MUTE
TV
CABLE
VCR
CH RTN
PIC SIZE
EXIT
LIGHT
STOP SOURCE
ADV/
PIP CH
ADV/
PIP CH
FAV
FAV
PLAY PIP
REC
TV/VCR
REW
FF
STILL
LOCATE SWAP
FAVORITE
MENU/
STROBE
ENTER
To control a cable TV converter:
Program the remote control to recognize the brand of your
converter. The shaded buttons shown at right will control the
cable TV converter.
Set the TV/CABLE/VCR switch to the CABLE position.
converter. The shaded buttons shown at right will control the
cable TV converter.
Set the TV/CABLE/VCR switch to the CABLE position.
Programming the remote control for use with a
VCR or a cable TV converter
VCR or a cable TV converter
This remote control is pre-programmed to operate Toshiba VCRs. To
use VCRs or cable converters other than Toshiba models, you must
follow the steps below before you operate your remote control.
use VCRs or cable converters other than Toshiba models, you must
follow the steps below before you operate your remote control.
1. Refer to the “VCR code table” or “Cable TV converter code
table” on pages 16-17 to find the number that corresponds to the
brand name of your VCR or converter.
If more than one number is listed, try each one separately until
you find the one that works.
brand name of your VCR or converter.
If more than one number is listed, try each one separately until
you find the one that works.
2. If you are reprogramming the remote control to operate your:
• VCR, set the TV/CABLE/VCR switch on the remote control
to VCR.
• Cable converter, set the TV/CABLE/VCR switch on the
remote control to CABLE.
3. While holding down the RECALL button, press the Number
buttons (0-9) to enter the three-digit code of your brand of VCR
or converter.
or converter.
4. Point the remote control at the VCR or converter and press
POWER to test the code.
If the VCR or converter turns on, you have entered the correct
code.
If the VCR or converter does not respond to the remote control,
you may have entered the wrong code. Repeat steps 1-4 with
another code.
If the VCR or converter turns on, you have entered the correct
code.
If the VCR or converter does not respond to the remote control,
you may have entered the wrong code. Repeat steps 1-4 with
another code.
5. Reset the TV/CABLE/VCR switch to TV to control the TV.
For future reference, write down the code numbers you used:
VCR code
_____________________
Cable code
_____________________
Note:
• Each time you replace the batteries, you
• Each time you replace the batteries, you
must reprogram the remote control.
• Some newer VCRs are capable of working
on either of two remote codes. These VCRs
have a switch labeled “VCR1/VCR2.”
have a switch labeled “VCR1/VCR2.”
If your VCR has this kind of switch, it may
not respond to any of the code numbers for
your VCR brand name. In this case, set the
switch to the other position (VCR1 or
VCR2) and reprogram the remote control.
not respond to any of the code numbers for
your VCR brand name. In this case, set the
switch to the other position (VCR1 or
VCR2) and reprogram the remote control.
POWER
Channel
yz
Channel
Number
Number
Enter
RECALL