temco-tool 39rdvdsn Manuel D’Utilisation
25
RDVDSN Series Direct Vent Gas Fireplace
20007894
1. STOP! Read the safety information above.
2. Set the thermostat, if used, to the lowest set-
2. Set the thermostat, if used, to the lowest set-
ting.
3. Turn off electric power to the appliance.
4. This appliance is equipped with an ignition
4. This appliance is equipped with an ignition
device which automatically lights the burner. Do
not try to light the burner by hand.
not try to light the burner by hand.
FOR YOUR SAFETY READ BEFORE LIGHTING
•
If you cannot reach your gas supplier, call
the Fire Department
the Fire Department
C. Use only the wall switch or remote control switch
to turn the gas control on/off. Never use tools. If
the knob will not push in or turn by hand, do not
try to repair it, call a qualified service technician.
Applying force or any attempted repair may result
in a fire or explosion.
the knob will not push in or turn by hand, do not
try to repair it, call a qualified service technician.
Applying force or any attempted repair may result
in a fire or explosion.
D. Do not use this fireplace if any part has been
under water. Immediately call a qualified service
technician to inspect the heater and to replace
any part of the control system and any gas con-
trol which has been under water.
technician to inspect the heater and to replace
any part of the control system and any gas con-
trol which has been under water.
A. This heater has a pilot which must be lit manu-
ally. When lighting the pilot follow these instruc-
tions exactly.
tions exactly.
B. BEFORE LIGHTING smell all around the heater
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will
settle on the floor.
because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS
•
Do not try to light any fireplace
•
Do not touch any electric switch
•
Do not use any phone in your building
•
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
neighbor’s phone. Follow the gas supplier’s
instructions.
To Turn Off Gas to Heater
Lighting and Operating Instructions
1. Set thermostat to lowest setting.
2. Turn off all electric power to the appliance if
2. Turn off all electric power to the appliance if
service is to be performed.
Lighting Instructions
WARNING:If you do not follow these instructions exactly, a fire or explosion
may result causing property damage, personal injury or loss of life.
ON
OFF
T209
electronic gas
control on/off
1/04
5. Open the access door located at the bottom of
the appliance to expose the controls.
6. Turn gas line valve to “ON”.
7. Wait five (5) minutes to clear out any gas, then
7. Wait five (5) minutes to clear out any gas, then
smell for gas, including near the floor. If you
smell gas, STOP! Follow “B” in the safety infor-
mation above. If you do not smell gas, go to the
next step.
smell gas, STOP! Follow “B” in the safety infor-
mation above. If you do not smell gas, go to the
next step.
8. Replace control access panel.
9. Turn on all electric power to the appliance.
10. Set thermostat to desired setting (if available).
11. If the appliance will not operate, follow the in-
9. Turn on all electric power to the appliance.
10. Set thermostat to desired setting (if available).
11. If the appliance will not operate, follow the in-
structions “To Turn OFF Gas to Appliance” and
call your service technician or gas supplier.
call your service technician or gas supplier.
3. Open the control access door.
4. Turn gas line valve to the “OFF” position.
5. Close the control access door.
4. Turn gas line valve to the “OFF” position.
5. Close the control access door.