Sansui hdlcd185w Manuel D’Utilisation

1

To turn on the TV, press   (POWER) (It may take 

approx. 10 seconds for a picture to appear on 

screen.). The Auto Setup function begins.

Automatic Search

Start

TV Location

Store

E-POP Demo

On

Signal Type

Cable

2

Press ▲ or ▼ to select “TV Location”, then press 

◀ or ▶ to select “Home” or “Store”. This product 

qualifies for ENERGY STAR In Home mode 

default setting.
NOTE:

This unit has been preset to STORE brightness. 

This setting does not qualify under ENERGY 

STAR. To reduce brightness and energy 

consumption, change setting to ‘HOME’. This 

setting does qualify under ENERGY STAR.

The device may not conform to the ENERGY 

STAR standard after Reset is performed or the 

Backlight is adjusted.

•

•

3

Press ▲ or ▼ to select “E-POP Demo”, then press 

◀ or ▶ to select “On” or “Off”.

On: A TV feature introduction will be popped up 

at the bottom of the screen.

Off: Turn off the E-POP Demo feature.

4

Press ▲ or ▼ to select “Signal Type”, then press 

◀ or ▶ to select “Air” or “Cable”.

5

Press ▲ or ▼ to select “Automatic Search”, then 

press ▶ or ENTER. 

6

“Auto Setup” will begin. After the Auto Setup 

is completed, the TV channel appears on the 

screen.

Depending on the reception condition, it may 

take up to 30 minutes to complete memorizing 

digital cable channels. Please allow the 

process to complete without interruption.

•

If you press EXIT in the process of “Auto Setup”, 

the Auto Setup stops and changes to the normal 

screen.
When you make a menu selection, your changes 

occur immediately. You do not have to press EXIT to 

see your changes.

TV operation
1

To turn on the TV, press   (POWER).

(It may take approx. 10 seconds for a picture to 

appear on screen.)

2

Adjust the volume level by pressing VOL + or – . 

The volume level will be indicated on the screen 

by green bars. As the volume level increases, so 

do the number of bars. If the volume decreases, 

the number of green bars also decreases.

•

•

3

Set the Signal Type option to the appropriate 

position (see “Air/Cable selection” on page 18).

4

Press the Direct Channel Selection (0-9, –) 

buttons to select the channel.

(If you press only channel number, channel 

selection will be delayed for a few seconds.)
TO SELECT ANALOG CHANNELS

1-9: 

Press 1-9 as needed. Example, to 

select channel 2, press 2, then press 

ENTER.

10-99: 

Press the 2 digits in order. Example, 

to select channel 12, press 1, 2, then 

press ENTER.

100-135:  Press the 3 digits in order. Example, to 

select channel 120, press 1, 2, 0, then 

press ENTER.

Press the first 1-3 digits, then press the – button, 

followed by the remaining number.

Example, to select channel 15-1, press 1, 5, –, 1, 

then press ENTER.

If a channel is selected with only audio content, 

“Audio only” will be displayed on the screen.

If a channel is selected with a weak digital 

signal, “Digital channel signal strength is low” 

will be displayed on the screen.

  The same program may be available on either 

an analog channel or a digital channel. You may 

choose to watch either format.

If a channel is selected to which you have not 

subscribed, “Digital channel is encrypted” will 

be displayed on the screen.

•

•

•

VHF

2-13

VHF

2-13

UHF

14-69

STD/HRC/IRC

14-36 (A) 

(W)

37-59 (AA) 

(WW)

60-85 (AAA) 

(ZZZ)

86-94 (86) 

(94)

95-99 (A-5) 

(A-1)

100-135 (100) 

(135)

01 (4A)

If a channel with no broadcast is selected, the 

sound will automatically be muted.

It may take a few seconds for a digital channel 

picture to appear on screen after being selected.

To view a signal from another device connected 

to your TV, such as a VCR player, press INPUT 

SELECT, then press ▲ or ▼ or corresponding 

Number buttons (0-4), then press ENTER. You can 

select TV, Video, Component, HDMI or PC depending 

on which input jacks you used to connect your 

devices.

•

•

3EZ0601A_En.indd   15

3EZ0601A_En.indd   15

6/6/11   8:51:13 PM

6/6/11   8:51:13 PM