Philips fw-p75 Manuel D’Utilisation
21
English
3139 116 19761
TIMER
STEREO
FM
BACK
HSD
REPEAT
LW
MW
AM
T.A.
NEWS
SOUND NAVIGATION
DIGITAL SOUND
CONTROL
DYNAMIC BASS
BOOST
BOOST
TAPE
CD
PROG
CLOCK/
TIMER
TIMER
NEWS!
RDS
DOLBY B
NR
DUB
(HSD)
REC
STANDBY
ON
ON
SIDE A•B
A.REV
TUNER
AUX
PRESET ▲
▲
STOP
• CLEAR
SEARCH • TUNING
PLAY
PAUSE
PREV
NEXT
MINI HIFI SYSTEM
C D 1 • 2 • 3
CDR / VIDEO
BAND
TAPE 1 • 2
FRONT
60Hz
500Hz
250Hz
1KHz
2KHz
4KHz
8KHz
VOLUME
REC
PROGRAM
S
S
L
R
C
PRO LOGIC
SIDE
SWITCH OFF DOLBY PRO LOGIC
WHEN RECORDING
Notes:
– It is not possible to change tape side
– It is not possible to change tape side
during recording.
– For recording, use only tape of IEC type I
(normal tape) or IEC type II (Cr02).
– The tape is secured at both ends with
leader tape. At the beginning and end of
tape, nothing will be recorded for six to
seven seconds.
tape, nothing will be recorded for six to
seven seconds.
– The recording level is set automatically,
regardless of the position of Volume,
DBB or DSC.
DBB or DSC.
– To prevent accidental recording, break
out the tab on the left shoulder of the
tape side you want to protect.
tape side you want to protect.
– If “CHECK TAPE” is displayed, the
protection tab has been broken. Put a
piece of clear adhesive tape over the
opening. Do not cover the Cr02 tape
piece of clear adhesive tape over the
opening. Do not cover the Cr02 tape
detection hole when covering the tab
opening.
opening.
Digital Recording via Digital
Out
Out
For CD digital recording, please refer to the
Instructions Manual of the CD Recorder,
digital audio equipment, etc.
Instructions Manual of the CD Recorder,
digital audio equipment, etc.
RECORDING
Recording from other sources
(only on tape deck 2)
1 Press TAPE ( TAPE 1•2 ) to select tape
1 Press TAPE ( TAPE 1•2 ) to select tape
deck 2.
2 Load a blank tape into tape deck 2 with
the open side downward.
3 Press í or ë to select the recording
tape side
(see Tape Side under TAPE
section).
4 Press CD, TUNER or AUX.
• Start playback of the selected source.
5 Press REC to start recording.
• Start playback of the selected source.
5 Press REC to start recording.
™ The
REC
starts flashing.
6 Press Ç to stop recording.
Notes:
– Only
– Only
å
å
å
å
å or ∂
∂
∂
∂
∂ mode is available
during recording .
– During recording, it is not possible to
listen to another source.
Dubbing tapes
(from tape deck 1 to
tape deck 2)
1 Press TAPE ( TAPE 1•2 ) to select tape
1 Press TAPE ( TAPE 1•2 ) to select tape
deck 2.
2 Load the prerecorded tape into tape
deck 1 with full spool to the left and a
blank tape into tape deck 2 with full
spool aside.
blank tape into tape deck 2 with full
spool aside.
3 Press í or ë to select the recording
tape side
(see Tape Side under TAPE
section).
pg 01-26/P75/22-Eng
3/6/00, 12:40 PM
21