mitutoyo 506s. 512s Manuel D’Utilisation

 

（1）Specifications 

 

MODEL 

 LSM-500S 

Order No. 

 544-532 

Applicable display unit 

 LSM-6200 

Laser scanning range 

mm(inch) 

Up to 12.5(.49”)   

(Detecting regions is limited to about 10 mm (.4”) approx.) 

Measuring range 

mm(inch) 

0.005 to 2 (.0002” to .08”) 

0.1 to 2 (.004” to .08”)[*1] 

Resolution  

µm(inch) 

0.01 to 10 (.000001” to .0005”) [Selectable] 

Repeatability[*2] µm(inch) 

±0.03 (±.0000012

”) [*3] 

Linearity [*2] 

µm(inch) 

±0.3 (±.000012

”) [*4] 

Positional error [*2][*5] 

µm(inch) 

±0.4 (±.000016

”) 

Measuring region 

mm(inch) 

1 × 2 (.04

”

 × .08”) 

[Optical axis direction × Scanning direction] 

Number of scans for averaging 

scan 

16 to 2048[*6] 

Laser classification 

 

Class 2 (Max. Output:1.3mW with a scanning laser, semiconductor laser: 

wavelength 650nm) 

Number of laser scans 

/sec 

3200 

Laser scanning rate 

m/sec (inch/sec) 

76(2992

”/sec) 

Protection level 

 

IP64 

Temperature 0 

°C to 40 °C 

Humidity 

35 %RH to 85 %RH [without condensation] 

Operation environment 

Altitude 

2000 m or less 

Temperature -15 

°C to 55 °C 

Storage environment 

Humidity 

35 %RH to 85 %RH [without condensation] 

[*1]：Measuring range available when set to “No extra-fine wire measurement” or “Edge specification” in the basic setup 

mode. 

[*2]：Environment for accuracy validation: 20

°C

 ± 1

°C

 temperature; 50% ± 10% humidity. 

[*3]：The value of ±2

σ with a 2mm-diameter gage has been measured for two minutes with a measurement interval of 

0.32 seconds, where 

σ is the standard deviation. 

[*4]：The value of measurements in the center of the measurement region. 
[*5]：Error due to the positional shift of the workpiece in the optical axis direction or scanning direction. 
[*6]：Averaging scans between 1 and 8 times can be made if “No extra-fine wire measurement” is specified in the basic 

setup mode. The measuring range, however, is limited to 0.1 mm to 2 mm in this case. 

 
（2）Standard accessories 

 

Part No. 

Item 

Qt. 

― 

ID unit [*7] 

1 

02AGN770A 

Signal cable (5m / 16ft) 

1 

99MBC094A User’s 

manual 

 

1 

[*7]：The ID unit stores data unique to the measuring unit. A replacement ID unit is available at extra cost. 

 

（3）Optional accessories 
 

Order No. 

Item 

02AGD110 

Calibration gages set 

 φ 0.1 mm   φ 2 mm 

02AGD200 

Guide pulley unit for LSM-500H (also available for LSM-500) 

02AGD220 

Air-blow unit for LSM-500H (also available for LSM-500) 

02AGN780A/B 

Extension signal cables ( 5m/10m)(16ft/32ft)[*8] [*9] 

[*8]：

The signal cable can be extended up to 20 m(64ft). 

[*9]：The length of the 

signal cable

 other than the standard, may affect the accuracy .