Gemini CFX-40 Manuel D’Utilisation

VOLTAGE SELECTOR:  To set the proper voltage, adjust the VOLTAGE SELECTOR (1) switch to 115 or 230 volts.

POWER JACK (AC IN):  Connect the power plug into the POWER JACK (2) for power.

REMOTE CONTROL:  Use the included CABLE & REMOTE CONTROL (3) jacks to connect the REMOTE CONTROL to the MAIN UNIT.

LINE OUTPUT JACKS:  LINE OUTPUT JACKS (4) provide stereo sound via included RCA cables to your mixer or receiver.

NOTE:  MAKE SURE CABLES ARE PLUGGED IN TIGHT FOR OPTIMAL SOUND.

DIGITAL OUTPUT (COAXIAL):  Use the COAXIAL (5) jack to connect to any type of device that accepts digital signals.

POWER:  Press the POWER (6) button to turn on the CD player.

NOTE:  MAKE SURE VOLTAGE SELECTOR SWITCH (1) IS SET BEFORE USE.

DISC TRAY:  Put a CD in the DISC TRAY (7) after pressing STOP (8); trays hold both 12 cm and 8 cm CDs.

STOP:  Tap the STOP (8) button once to STOP the CD, twice to open the DISC TRAY (7), and a third time to close the tray.

DISPLAY:  The DISPLAY (9) shows the various functions for the CD Player.  See FUNCTION DESCRIPTIONS for details.

PLAYBACK DISPLAY BAR:  The PLAYBACK DISPLAY BAR (10) shows the TIME ELAPSED and TIME REMAINING.

PLAY/PAUSE:  Press PLAY/PAUSE (11) button to activate PLAY or PAUSE mode.  See CUE or ROBO START INSTRUCTIONS for details.

CUE/PREVIEW:  Tap CUE/PREVIEW (12) to come back to a set CUE or press and hold to PREVIEW from a CUE POINT, refer to CUE INSTRUCTIONS.

TRACK:  Press the TRACK (13) buttons to select which TRACK to play.

SEARCH:  Use the SEARCH (14) buttons to scan forward and reverse directions on a TRACK.

TIME:  Tap the TIME (15) button to switch the TIME preference in three modes:  ELAPSED, REMAIN, TOTAL REMAIN.

SINGLE:  Tap SINGLE (16) for SINGLE AUTO CUE, CONTINUOUS, and NORMAL modes.

FLY CUE:  FLY CUE (17) sets a SEAMLESS LOOP CUE POINT on the fly.

CUE-B/EXIT:  Press CUE-B/EXIT (18) in PLAY mode, after a CUE POINT is memorized to start a LOOP, press again to exit LOOP.

RELOOP STUTTER:  To play from a saved CUE POINT or a LOOP, press RELOOP STUTTER (19) to play the LOOP or the CUE again.

MEMO (CUE 1-3):  Press MEMO (20), then select a CUE POINT from CUE1-3 (20) followed by the same number again to set a CUE POINT.

Press CUE1-3 (20) to play from the set CUE POINT.

JOG WHEEL:  The JOG WHEEL (21) has various functions such as PITCH BEND, CUEING, VINYL MODE, and EFFECT PARAMETERS.

JOG MODE:  Press to change the JOG MODE (22) of the JOG WHEEL (21) from CD to VINYL mode.

EFFECT:  Press an EFFECT button:  FILTER, ZOOM, TRANS, or ECHO (23), to activate an EFFECT.  Tap the EFFECTS (23) button to release.

MASTER TEMPO:  Pressing MASTER TEMPO (24) locks the PITCH of a track with no change in vocal or instrument tone.

PITCH BEND:  Buttons for PITCH BEND (25), lower or raise the pitch percentage (- or + 4%) when pressed.

PITCH:  The PITCH (26) button activates the PITCH CONTROL SLIDE (27).

PITCH SELECT (4%, 12%, 24%, & 100%):  Use the PITCH SELECT (27) button to change the PITCH settings from 4%, 12%, & 24%.

Press and hold for 100% PITCH.

PITCH CONTROL SLIDE:  Moving the PITCH CONTROL SLIDE (28) up or down will lower or raise the pitch percentage.

ROBO START:  Using ROBO START (29) enables you to alternate play between two CDs using both sides.

PGM (PROGRAM):  First choose a side by selecting A or B (30).  For track programming press PGM (30) then enter a track number followed by

PGM (30) and so-forth.  For direct selection press a TRACK NUMBER followed by SET (30) then PLAY/PAUSE (11) to jump to that track.

NOTE:  FOR FURTHER EXPLANATION PLEASE SEE PGM SECTION.