Radio Shack 43-3821 Manuel D’Utilisation
In
s
ta
lla
ti
o
n
10
6. Lift the base’s antenna to a vertical position.
%
100'%6+0)
."%
*#4)+0)
"
#0&
"
4
'2.#%+0)
"
6*'
"$
#66'4;
"2
#%-
The phone comes with a rechargeable Ni-Cd
(nickel-cadmium) battery pack installed in the
handset, but not connected. Before using your
phone, you must connect the battery pack, then
charge it for about 24 hours.
(nickel-cadmium) battery pack installed in the
handset, but not connected. Before using your
phone, you must connect the battery pack, then
charge it for about 24 hours.
1. Press down and slide off the battery pack
compartment cover.
2. Lift the battery pack out of the compartment.
3. Plug the battery
pack’s connector
into the socket in
the compartment.
The connector fits
only one way.
into the socket in
the compartment.
The connector fits
only one way.
4. Put the battery pack in the compartment.
5. Replace the cover.
To charge the battery pack, place the handset on
the base, face up or down. The base’s CHARGE/IN
USE indicator lights.
the base, face up or down. The base’s CHARGE/IN
USE indicator lights.
#"
Recharge the battery pack when the handset beeps
and TALK/BATT flashes.
and TALK/BATT flashes.
±ý
When you first use the phone after charging or
recharging the battery pack, the phone might not
work and you might hear error beeps. If this
happens, return the handset to the base for about 5
seconds to reset the security access-protection
code.
recharging the battery pack, the phone might not
work and you might hear error beeps. If this
happens, return the handset to the base for about 5
seconds to reset the security access-protection
code.
Using a pencil eraser, clean the charging contacts
on the handset and the base about once a month.
on the handset and the base about once a month.
#
"+/2146#06"
#
Be sure the battery pack is
properly connected before
you try to charge it. The
CHARGE/IN USE indicator
lights when the handset is
on the base even if the
battery pack is not
connected properly.
properly connected before
you try to charge it. The
CHARGE/IN USE indicator
lights when the handset is
on the base even if the
battery pack is not
connected properly.
±
"016'"
±
"
•
If the phone does not
work, recharge the
battery pack. (The
battery power might be
too low for the display to
operate.)
work, recharge the
battery pack. (The
battery power might be
too low for the display to
operate.)
•
If the battery pack
becomes weak during a
call, the handset beeps
about every 3 seconds
and TALK/BATT flashes.
When this happens, you
cannot make a call on
the phone until you
recharge the battery
pack.
becomes weak during a
call, the handset beeps
about every 3 seconds
and TALK/BATT flashes.
When this happens, you
cannot make a call on
the phone until you
recharge the battery
pack.
•
If the battery pack is
completely discharged
or the base loses power
while the handset is
away from it, place the
handset on the base to
reset the security
access-protection code.
If it was the handset that
lost power, recharge the
battery pack.
completely discharged
or the base loses power
while the handset is
away from it, place the
handset on the base to
reset the security
access-protection code.
If it was the handset that
lost power, recharge the
battery pack.
43-3821.fm Page 10 Friday, May 10, 2002 10:08 AM