Hitachi 27mm20b Manuel D’Utilisation
USING THE REMOTE TO CONTROL YOUR VCR FUNCTIONS- 16 -
14 SLEEP Button
Press this button to display the SLEEP TIMER in the lower left corner of the screen. Every subsequent press of
this button will add 15 minutes to the timer, up to a maximum of three hours.
Press this button to display the SLEEP TIMER in the lower left corner of the screen. Every subsequent press of
this button will add 15 minutes to the timer, up to a maximum of three hours.
USING THE REMOTE TO CONTROL YOUR VCR FUNCTIONS
Operating the precoded function for your VCR
This remote is designed to operate different types of VCRs. You must first program the remote to match the
remote system of your VCR. (Refer to page 26.)
remote system of your VCR. (Refer to page 26.)
1. Turn on your VCR.
2. Aim the remote control at the front of your VCR.
3. Press the VCR button to switch to the VCR precoded mode.
4. While holding down the VCR button on the remote, enter the two digit preset code that matches your VCR as
shown on page 26. The remote will turn off your VCR when the correct two digit preset code is entered. When this
occurs, the remote control is programmed for your VCR. If the VCR does not turn off after five seconds, try a
different two digit preset code.
5. The remote will now control your VCR.
2. Aim the remote control at the front of your VCR.
3. Press the VCR button to switch to the VCR precoded mode.
4. While holding down the VCR button on the remote, enter the two digit preset code that matches your VCR as
shown on page 26. The remote will turn off your VCR when the correct two digit preset code is entered. When this
occurs, the remote control is programmed for your VCR. If the VCR does not turn off after five seconds, try a
different two digit preset code.
5. The remote will now control your VCR.
NOTES:
1. If your VCR cannot be operated after performing the above procedures, your VCR code has not been precoded
into the remote.
2. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult
your VCR operating guide.
3. The remote control will remember the codes you have programmed in until the batteries are removed from the
remote control. After replacing the batteries repeat the entire programming procedure stated above.
4. If your VCR does not have a power function, the remote will issue the CHANNEL UP (
1. If your VCR cannot be operated after performing the above procedures, your VCR code has not been precoded
into the remote.
2. In the unlikely event that your VCR cannot be operated after performing the above procedures, please consult
your VCR operating guide.
3. The remote control will remember the codes you have programmed in until the batteries are removed from the
remote control. After replacing the batteries repeat the entire programming procedure stated above.
4. If your VCR does not have a power function, the remote will issue the CHANNEL UP (
) function.
1 VCR Button
This allows the remote to control your VCR by setting it to VCR mode.
This allows the remote to control your VCR by setting it to VCR mode.
2 PRECODED VCR Buttons
These buttons transmit the chosen precoded VCR codes.
These buttons transmit the chosen precoded VCR codes.
3 EXCLUSIVE TV Buttons
These buttons are for operating the TV.
If your VCR is a Hitachi brand, the MENU button will start your VCR on-screen display.
These buttons are for operating the TV.
If your VCR is a Hitachi brand, the MENU button will start your VCR on-screen display.
4 LST-CH Button
If your VCR has an "ENTER" function, this button will send the chosen VCR "+ "ENTER" code.
If your VCR has an "ENTER" function, this button will send the chosen VCR "+ "ENTER" code.
5 SLEEP Button
If your VCR has a "+100" function, this button will send the chosen VCR "+100" code.
If your VCR has a "+100" function, this button will send the chosen VCR "+100" code.
NOTE: To use VCR RECORD, press the REC button twice.