INSTEON 2472d Manuel D’Utilisation
Page 12 of 13 2472D - Rev: 1/21/2014 7:48 AM
Problem
Possible Cause
Solution
slowing down communication signals to
OutletLinc.
OutletLinc.
If the above doesn’t work, perform a factory reset
on the controller.
on the controller.
The load turned on by
itself.
itself.
Another controller, a timer or stray X10
signals could have triggered OutletLinc.
signals could have triggered OutletLinc.
Monitor for recurrence and remove reason if you
can determine what it is. If necessary perform a
factory reset.
can determine what it is. If necessary perform a
factory reset.
The OutletLinc sensed a change in the
connected table lamp and triggered the
load sense feature.
connected table lamp and triggered the
load sense feature.
Disable load sense (via compatible software such
as HouseLinc) or make sure a standard
incandescent bulb is used.
as HouseLinc) or make sure a standard
incandescent bulb is used.
The load doesn’t appear to
turn on right away.
turn on right away.
The ramp rate may be set too slow.
Set a faster ramp rate. See Setting the Ramp Rate.
OutletLinc is locked up.
A surge or excessive noise on the
power line may have glitched it.
power line may have glitched it.
Remove power to OutletLinc by turning off the
circuit breaker for five seconds, then turning it back
on. If that doesn’t work, perform a factory reset.
circuit breaker for five seconds, then turning it back
on. If that doesn’t work, perform a factory reset.
An LED bulb plugged into
OutletLinc does not turn
off completely when I send
an OFF command.
OutletLinc does not turn
off completely when I send
an OFF command.
Since LEDs require so little power, the
load sensing current that runs through
OutletLinc may be enough to power the
bulb.
load sensing current that runs through
OutletLinc may be enough to power the
bulb.
Add to the load with more LEDs or higher wattage
bulbs, generally higher than a 5 Watt load.
Add one incandescent bulb to soak up the sense
current.
bulbs, generally higher than a 5 Watt load.
Add one incandescent bulb to soak up the sense
current.
The OutletLinc LED is
blinking red even though I
haven’t put it into unlinking
mode.
blinking red even though I
haven’t put it into unlinking
mode.
The Outlet Dimmer Key may not be
properly installed.
properly installed.
Be sure the protruding magnet of the Outlet Dimmer
Key faces away from OutletLinc and towards the
plug of the load. See Installing OutletLinc Dimmer.
Key faces away from OutletLinc and towards the
plug of the load. See Installing OutletLinc Dimmer.
Be sure the Outlet Dimmer Key lies completely flush
against OutletLinc.
against OutletLinc.
If you have tried these solutions, reviewed this Owner’s Manual, and still cannot resolve an issue you are having with
OutletLinc, please call the INSTEON Support Line at 800-762-7845
OutletLinc, please call the INSTEON Support Line at 800-762-7845
Certification and Warranty
Certification
This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American
ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S. and Canadian
device safety standards, that the manufacturing site has been audited, and that the manufacturer has agreed to a program of quarterly factory follow-
up inspections to verify continued conformance.
This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American
ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S. and Canadian
device safety standards, that the manufacturing site has been audited, and that the manufacturer has agreed to a program of quarterly factory follow-
up inspections to verify continued conformance.
FCC and Industry Canada Compliance Statement
This device complies with FCC Rules Part 15 and Industry Canada RSS-210 (Rev. 7). Operation is subject to the following two conditions:
This device complies with FCC Rules Part 15 and Industry Canada RSS-210 (Rev. 7). Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux
conditions suivantes:
conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le
fonctionnement.
The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and
television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such
interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following
measures:
These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and
television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such
interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following
measures:
- Re-orient or relocate the receiving antenna of the device experiencing the interference
- Increase the distance between this device and the receiver
- Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver
- Consult the dealer or an experienced radio/TV technician
- Increase the distance between this device and the receiver
- Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver
- Consult the dealer or an experienced radio/TV technician
WARNING: Changes or modifications to this device not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
operate the equipment.