Funai drv-b2734 Manuel D’Utilisation
18
Get
tin
g S
tar
ted
ted
EN
Channel setting
Tuning of this unit to broadcast channels can be
performed in two ways.
performed in two ways.
Auto tuning
Programme the tuner to scan only the channels you
can receive in your area.
can receive in your area.
1
Press [STANDBY-ON] to turn on the
unit.
unit.
2
Turn the TV on and select the input
to which the unit is connected.
to which the unit is connected.
3
In stop mode, press [SETUP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
will appear.
4
Select “Channel” using
[Cursor
[Cursor
U / D], then press [ENTER].
5
Select “Auto Tuning” using
[Cursor
[Cursor
U / D], then press [ENTER].
The unit will start storing channels available in
your area.
your area.
Wait for several minutes to finish channel storing.
6
Press [SETUP] to exit.
You can select only the channels memorized in
this unit by using [PROG.
this unit by using [PROG.
U / D].
To select a channel
You can select a channel using [PROG.
You can select a channel using [PROG.
U / D], or
directly enter the channel using
[the Number buttons] on the remote control.
[the Number buttons] on the remote control.
To cancel auto tuning
Press [RETURN
Press [RETURN
R] or [SETUP] during scanning.
Note
• The selection will be affected by how you receive TV
channels in your local area.
• If the auto tuning is cancelled during scanning,
some channels not yet tuned may not be received.
• You cannot change the channel when either VCR or
DVD is in any recording mode (normal recording,
one-touch timer recording or timer recording).
one-touch timer recording or timer recording).
Manual tuning
Manually tune each channel.
1
In stop mode, press [SETUP].
“Easy Setting Menu” or “Advanced Setting Menu”
will appear.
will appear.
2
Select “Channel” using
[Cursor
[Cursor
U
/
D
], then press [ENTER].
3
Select “Manual Tuning” using
[Cursor
[Cursor
U
/
D
], then press [ENTER].
4
Select “Position” using
[Cursor
[Cursor
U / D], then press [ENTER].
5
Select the position number you wish
to use using [the Number buttons] or
[Cursor
to use using [the Number buttons] or
[Cursor
U / D], then press
[RETURN
R
].
You can select position numbers 01 to 99.
6
Select “Channel” using
[Cursor
[Cursor
U / D], then press [ENTER].
7
Press [Cursor
U / D] to start
scanning.
• The tuner will begin to search up or down
automatically. When a channel is found, the unit
will stop searching and the picture will appear
on the TV screen.
will stop searching and the picture will appear
on the TV screen.
• You can select a desired channel number using
[the Number buttons]. Refer to the following
Channel Plan table and press the three digits to
select the channel number.
(To select channel 4, press [0] first and then
press [0] and [4], or press [4]. Or press [4] and
then “– – 4” appears and wait for 2 seconds.)
Channel Plan table and press the three digits to
select the channel number.
(To select channel 4, press [0] first and then
press [0] and [4], or press [4]. Or press [4] and
then “– – 4” appears and wait for 2 seconds.)
• If this is the channel you want, press
[RETURN
R].
This unit can receive the Hyper and Oscar
frequency bands.
frequency bands.
P 01
Auto Tuning Now
Channel Plan
Ch. Indication
TV Channel
01 - 10
IRA - IRJ, GAP
21 - 69
E21 - E69
74 - 78
X, Y, Z, Z+1, Z+2
80 - 99, 100
S1 - S20, GAP
121 - 141
S21 - S41
Channel
12
Decoder
OFF
Skip
OFF
Position
P01
Manual Tuning
VCR DVD
DRV_B2737_B2734.book Page 18 Thursday, March 31, 2005 10:04 PM