Crestron b-g1-wpk Manuel D’Utilisation
Water Resistant Cover Kit for Single
Gang Wall Panel: B-G1-WPK
Gang Wall Panel: B-G1-WPK
The Crestron water resistant cover kit is specifically designed for ‘CNX-B Series’ single gang
wall panels. There are four urethane covers per kit. When properly installed the cover
prevents liquids and other air-born materials from settling directly onto the panel, but does not
interfere with regular usage of the unit.
No tools are required to install the B-G1-WPK cover; a silicone rubber adhesive is provided.
The panel must be properly setup (i.e., connected to the network) as outlined in the latest
version of the Single Gang Keypads Operations & Installation Guide (Doc. 8173) prior to
installing the water resistant cover. Complete the steps listed adjacent to the diagram for
installation.
wall panels. There are four urethane covers per kit. When properly installed the cover
prevents liquids and other air-born materials from settling directly onto the panel, but does not
interfere with regular usage of the unit.
No tools are required to install the B-G1-WPK cover; a silicone rubber adhesive is provided.
The panel must be properly setup (i.e., connected to the network) as outlined in the latest
version of the Single Gang Keypads Operations & Installation Guide (Doc. 8173) prior to
installing the water resistant cover. Complete the steps listed adjacent to the diagram for
installation.
GAP LOCATION
INSTALLED PANEL
MOUNTING
SURFACE
B-G1-WPK
COVER
1. Remove the backing
from the tape that
surrounds the perimeter
of the cover.
surrounds the perimeter
of the cover.
2. Place the cover over the
panel making sure that
the gap in the tape
perimeter is located at
the bottom.
the gap in the tape
perimeter is located at
the bottom.
3. Firmly press down the
cover so that it
completely encloses the
panel.
completely encloses the
panel.
4. Except for the gap at the
bottom, apply a bead of
silicone rubber adhesive
around the outer edge of
the cover (form a seal
with the mounting
surface).
silicone rubber adhesive
around the outer edge of
the cover (form a seal
with the mounting
surface).
5. Do not use the panel
while the adhesive cures
(typically 24 hours).
(typically 24 hours).
WARNING: Silicone rubber adhesive is an irritant to skin, eyes, and respiratory tract. Skin and eye
protection required. Avoid repeated or prolonged contact. Good ventilation is required.
protection required. Avoid repeated or prolonged contact. Good ventilation is required.
WARNING: To avoid shock hazard and possible damage to the unit, never install a touchpanel where it
may be exposed to rain or very high humidity. This kit is designed to resist water (eg. protect unit from
wet hands) and in no way provides waterproof protection.
may be exposed to rain or very high humidity. This kit is designed to resist water (eg. protect unit from
wet hands) and in no way provides waterproof protection.
Further Inquiries
If after reviewing this sheet for the B-G1-WPK, you still have questions, please take
advantage of Crestron's award winning customer service team by calling:
advantage of Crestron's award winning customer service team by calling:
•
In the US and Canada, call Crestron’s corporate headquarters at 1-888-CRESTRON
[1-888-273-7876].
[1-888-273-7876].
•
In Europe, call Crestron International at +32-15-50-99-50.
•
In Asia, call Crestron Asia at +852-2341-2016.
•
In Latin America, call Crestron Latin America at +5255-5093-2160.
•
In Australia and New Zealand, call Crestron Pacific at +613-9480-2999.
Crestron Electronics, Inc.
Water Resistant Cover Kit for Single Gang Wall Panel: B-G1-WPK
15 Volvo Drive
DOC. 6100
Rockleigh, NJ 07647
01.03
Tel: 888.CRESTRON
Specifications subject to change without notice.
Fax: 201.767.7576
www.crestron.com