Navman 5605 Manuel D’Utilisation
TRACKER 5505/5505i/5605 Installation and Operation Manual
7
NAVMAN
1-2 Cleaning and maintenance
The TRACKER screen is covered by a proprietary
anti-reflection coating. To avoid damage,
clean the screen only with a damp cloth and
mild detergent when dirty or covered in sea
salt. Avoid abrasive cleaners, petrol or other
solvents. If a plug-in card gets dirty or wet,
clean it with a damp cloth or mild detergent.
anti-reflection coating. To avoid damage,
clean the screen only with a damp cloth and
mild detergent when dirty or covered in sea
salt. Avoid abrasive cleaners, petrol or other
solvents. If a plug-in card gets dirty or wet,
clean it with a damp cloth or mild detergent.
To optimize performance, avoid walking on or
jamming cables and connectors.
Push the dust cover over the display when the
TRACKER is turned off.
jamming cables and connectors.
Push the dust cover over the display when the
TRACKER is turned off.
The NAVMAN TRACKER is a compact, rugged,
highly integrated marine chartplotter. It is easy
to use and has an easy to read colour display.
Complex functions can be performed with a few
key presses, taking the hard work out of boating.
This manual covers:
TRACKER 5505/5605
highly integrated marine chartplotter. It is easy
to use and has an easy to read colour display.
Complex functions can be performed with a few
key presses, taking the hard work out of boating.
This manual covers:
TRACKER 5505/5605
Colour display, external GPS antenna.
TRACKER 5505i
Colour display, internal GPS antenna.
The available functions, displays and setup
menus depend on the optional sensors and
instruments that are installed:
menus depend on the optional sensors and
instruments that are installed:
The Fuel functions require optional
petrol/gasoline, diesel or SmartCraft fuel
sensors to be installed and set up.
petrol/gasoline, diesel or SmartCraft fuel
sensors to be installed and set up.
1-1 Overview
SmartCraft engine functions require a
SmartCraft system to be installed. For
information on using SmartCraft, see
the SmartCraft Gateway Installation and
Operation Manual.
SmartCraft system to be installed. For
information on using SmartCraft, see
the SmartCraft Gateway Installation and
Operation Manual.
The TRACKER can send data to other
instruments, such as an autopilot, and
receive data from other instruments.
instruments, such as an autopilot, and
receive data from other instruments.
For information on installing options, see
section 15-2.
This manual describes how to install and
operate the TRACKER. Special terms are
explained in Appendix C. For maximum
benefit, please read this manual carefully
before installing and using the unit. For more
information on this instrument and other
Navman products, go to our website,
www.navman.com.
section 15-2.
This manual describes how to install and
operate the TRACKER. Special terms are
explained in Appendix C. For maximum
benefit, please read this manual carefully
before installing and using the unit. For more
information on this instrument and other
Navman products, go to our website,
www.navman.com.
1-3 Plug-in cards
The TRACKER can use two kinds of plug-in card:
C-MAP™ chart cards have chart details
required for navigating in a particular
region. When a chart card is plugged in, the
extra details automatically appear on the
TRACKER chart display.
required for navigating in a particular
region. When a chart card is plugged in, the
extra details automatically appear on the
TRACKER chart display.
The TRACKER can use NT, NT+ and NT-MAX
cards.
cards.
C-MAP™ user cards are used to store
navigation data. Each user card expands
the TRACKER memory and allows the data
to be transferred to another TRACKER easily
(see section 14).
navigation data. Each user card expands
the TRACKER memory and allows the data
to be transferred to another TRACKER easily
(see section 14).
Note: The older 5 volt user cards are not
supported.
supported.
1 Introduction
www.Busse-Yachtshop.de email: info@busse-yachtshop.de