Navman 5605 Manuel D’Utilisation
TRACKER 5505/5505i/5605 Installation and Operation Manual
26
NAVMAN
2 To insert a waypoint in the route by breaking
one leg into two:
i
i
Move the cursor to the leg you want to
break.
break.
ii Press
and select
Insert.
iii Move the cursor to where the new route
waypoint will be.
iv Press
.
3 To move a waypoint in the route:
i
Move the cursor to the waypoint to
move.
move.
ii Press
and select
Move.
iii Move the cursor to where the waypoint
will be.
iv Press
.
4 To remove a waypoint from the route:
i
Move the cursor to the waypoint to
remove from the route.
remove from the route.
ii Press
and select
Remove. The
waypoint is removed from the route, but
the waypoint is not deleted.
the waypoint is not deleted.
5 To start navigating the route
i
Press
and select
Start
6 To end creating the route
i
Press
and select
End
7 To delete the route
i
Press
and select
Delete
ii Select yes to confirm.
Tip: The distance and bearing calculator can
also be used to enter a course and save it as a
route (see section 3-3).
B. Creating a new route from the routes display
1 In the routes display, press
route (see section 3-3).
B. Creating a new route from the routes display
1 In the routes display, press
and
select
Create.
2 A new route, with a default name and no
waypoints, is displayed.
3 To change the route name:
i
Select the route name at the top of the
display and press
display and press
.
ii Change the name if necessary.
iii Press
iii Press
.
6-2 Managing routes
6-2-1 Creating a new route
A. Creating a new route from the chart display
While creating the route:
While creating the route:
Press
or
to change the range; scroll
the chart by moving the cursor to the edge
of the chart.
of the chart.
A data box at the bottom left of the display
shows the route name and total distance. If
the cursor is near a leg, it shows the length
and bearing of the leg as well.
shows the route name and total distance. If
the cursor is near a leg, it shows the length
and bearing of the leg as well.
The legs of a route must start and end at
waypoints. If a leg does not start or end at an
existing waypoint then a new waypoint will
be created automatically (to change the new
waypoint data, see section 5-2-7).
waypoints. If a leg does not start or end at an
existing waypoint then a new waypoint will
be created automatically (to change the new
waypoint data, see section 5-2-7).
You can not use a Danger waypoint in a
route.
route.
1 In the chart display, press
and select
New route.
2 The route is given a default name:
i
Change the name if necessary.
ii Select
Ok.
3 To enter the legs of the route:
i
Move the cursor to the start of the route
and press
and press
.
ii A waypoint is created with a default
name. to save this waypoint press enter,
to edit the waypoint refer to 5-2-7
to edit the waypoint refer to 5-2-7
iii Press
a dotted leg line is displayed
from the cursor to the previous waypoint
iv Move the cursor to the end of the first
leg and press
.
v Repeat i to iv until the last waypoint in
the route is placed and saved
vi Press
to complete the route
Menu options while creating a route:
1 To add a waypoint to the route
1 To add a waypoint to the route
i
Press
and select
Add.
CAUTION
!
!
CAUTION
DANGER
WARNING
After creating or changing a route, display
the route on the chart and check that it
does not cross land or dangerous water.
the route on the chart and check that it
does not cross land or dangerous water.
www.Busse-Yachtshop.de email: info@busse-yachtshop.de