IBM powerpc 750gx Manuel D’Utilisation
User’s Manual
IBM PowerPC 750GX and 750GL RISC Microprocessor
gx_02.fm.(1.2)
March 27, 2006
March 27, 2006
Programming Model
Page 65 of 377
2.1.2.2 Hardware-Implementation-Dependent Register 0 (HID0)
The Hardware-Implementation-Dependent Register 0 (HID0) controls the state of several functions within
750GX. HID0 can be accessed with mtspr and mfspr using SPR 1008.
750GX. HID0 can be accessed with mtspr and mfspr using SPR 1008.
EM
C
P
DB
P
EB
A
EB
D
Reserved
PA
R
DOZE
NA
P
SL
E
E
P
DP
M
RIS
E
G
Res
e
rv
ed
MU
M
NHR
ICE
DCE
IL
OCK
DLOCK
ICFI
DCFI
SP
D
IF
EM
SGE
DCFA
BT
IC
Res
e
rv
ed
AB
E
BH
T
Res
e
rv
ed
NOOP
TI
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
Bits
Field Name
Description
0
EMCP
Enable MCP. The primary purpose of this bit is to mask out further machine-check excep-
tions caused by assertion of MCP, similar to how MSR[EE] can mask external interrupts.
0
tions caused by assertion of MCP, similar to how MSR[EE] can mask external interrupts.
0
Masks MCP. Asserting MCP does not generate a machine-check exception or a
checkstop.
checkstop.
1
Asserting MCP causes a checkstop if MSR[ME] = 0 or a machine-check excep-
tion if ME = 1.
tion if ME = 1.
1
DBP
Disable 60x bus address-parity and data-parity generation.
0
0
Parity generation is enabled.
1
Disable parity generation. If the system does not use address or data parity and
the respective parity checking is disabled (HID0[EBA] or HID0[EBD] = 0), input
receivers for those signals are disabled, require no pull-up resistors, and thus
should be left unconnected. If all parity generation is disabled, all parity checking
should also be disabled and parity signals need not be connected.
the respective parity checking is disabled (HID0[EBA] or HID0[EBD] = 0), input
receivers for those signals are disabled, require no pull-up resistors, and thus
should be left unconnected. If all parity generation is disabled, all parity checking
should also be disabled and parity signals need not be connected.
2
EBA
1
Enable/disable 60x bus address-parity checking
0
Prevents address-parity checking.
1
Allows an address-parity error to cause a checkstop if MSR[ME] = 0 or a
machine-check exception if MSR[ME] = 1.
machine-check exception if MSR[ME] = 1.
EBA and EBD allow the processor to operate with memory subsystems that do not gener-
ate parity.
ate parity.
3
EBD
1
Enable 60x bus data-parity checking
0
0
Parity checking is disabled.
1
Allows a data-parity error to cause a checkstop if MSR[ME] = 0 or a machine-
check exception if MSR[ME] = 1.
check exception if MSR[ME] = 1.
EBA and EBD allow the processor to operate with memory subsystems that do not gener-
ate parity.
ate parity.
4
—
Reserved. Must set to 0.
5
—
Not used. Defined as EICE on some earlier processors.
6
—
Reserved. Must set to 0.
7
PAR
Disable precharge of ARTRY.
0
Precharge of ARTRY enabled.
1
Alters bus protocol slightly by preventing the processor from driving ARTRY to
high (negated) state. If this is done, the system must restore the signals to the
high state.
high (negated) state. If this is done, the system must restore the signals to the
high state.
8
DOZE
2
Doze mode enable. Operates in conjunction with MSR[POW].
0
0
Doze mode disabled.
1
Doze mode enabled. Doze mode is invoked by setting MSR[POW] while this bit
is set. In doze mode, the phase-locked loop (PLL), time base, and snooping
remain active.
is set. In doze mode, the phase-locked loop (PLL), time base, and snooping
remain active.
1. For additional information, see Section 11.9, Checkstops, on page 361.
2. For additional information about power-saving modes, see Table 10-2, HID0 Power Saving Mode Bit Settings, on page 337.
2. For additional information about power-saving modes, see Table 10-2, HID0 Power Saving Mode Bit Settings, on page 337.