JL Audio sb-n-350-10w3v3 Manuel D’Utilisation
Specifications:
Enclosure Type: Acoustical Suspension(Sealed)
Driver Type: 2) 10W3v2-D4
Nominal Impedance: 4
Enclosure Type: Acoustical Suspension(Sealed)
Driver Type: 2) 10W3v2-D4
Nominal Impedance: 4
Ω
Cont. Power Handling: 600Watts
JL Audio recommends using a high quality amplifier such as the JL Audio 500/1. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the 500/1 when being used to power your Stealthbox®.
crossover, infrasonic filter and equalizer settings for the 500/1 when being used to power your Stealthbox®.
Included Hardware:
2) 3/8” Split Lock Washers
2) 3/8” Flat Washers
2) 3/8” x 1-1/4” Fender Washers
2) 3/8”x 2-/1/4” Socket Cup Set Screws
2) 3/8” Hex Nuts
2) 3/8” Split Lock Washers
2) 3/8” Flat Washers
2) 3/8” x 1-1/4” Fender Washers
2) 3/8”x 2-/1/4” Socket Cup Set Screws
2) 3/8” Hex Nuts
10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: 954.443.1100 Fax: 954.443.1111
The JL Audio 500/1 is a very versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
about installing and tuning this amplifier.
➔
➔
➔
STEP 24: Set the Stealthbox into position in the
vehicle. Placing the socket cup set screws through the
cut carpet and existing holes from STEP19 & 20.
vehicle. Placing the socket cup set screws through the
cut carpet and existing holes from STEP19 & 20.
Route the woofers’ wiring behind the enclosure to
the large hole at the far end of the passenger side
cargo area. Identified by the white circle.
the large hole at the far end of the passenger side
cargo area. Identified by the white circle.
Route the wiring down through this hole to the glove
box cavity for the connection to an amplifier.
box cavity for the connection to an amplifier.
STEP 25: The socket cup set screws are protruding
into the glove box/factory woofer area. Place the sup-
plied fender washer, lock washer and hex nut onto
each socket cup set screws. Indentified by the black cir-
cle in STEP 24.
into the glove box/factory woofer area. Place the sup-
plied fender washer, lock washer and hex nut onto
each socket cup set screws. Indentified by the black cir-
cle in STEP 24.
If needed, expose more length of the socket cup set
screws. Secure tightly.
screws. Secure tightly.
*Make sure the Stealthbox is centered with
the strut tower brace.*
the strut tower brace.*
STEP 26: Reassemble the vehicle’s panels in
reverse order of disassembly.
reverse order of disassembly.
➔
S B - N - 3 5 0 / 1 0 W 3 v 2 , J L AU D I O, I n c 2 0 0 4
S h e e t S K U # 0 1 1 1 8 7 R ev i s i o n 2 / 1 1 / 2 0 0 4
Pa g e 4
w w w . j l a u d i o . c o m
Mid/High Frequency Driver Information:
CONGRATULATIONS!
INSTALL COMPLETE.
INSTALL COMPLETE.
XR650-CSi
VR650-CXi
Front Location Driver Size:
6.5”
6.5”
Applicable JL Audio Products:
XR,VR & TR650-CSi
XR,VR & TR650-CSi
Rear Location Driver Size:
6.5”
6.5”
Applicable JL Audio Products:
XR,VR & TR650-CXi
XR,VR & TR650-CXi
Cont.
From
Previous
Page
➔
➔