beiter wh Manuel D’Utilisation

Eventually press the vane 
on the shaft with your 
thumb on the medium 
sector (should not be 
necessary, if the shaft has 
been cleaned well!).

You may fletch your vanes 
straight (parallel to the 
drawn line) or 1° off-set: 
simply install the red 
bushing delivered with the 
Beiter Wing-Holder 
over the front pin (Point-
>), by pressing it in.  - 
Pic. 9

pic. 1

pic. 2

pic. 4

pic. 3

pic. 9

pic. 7

pic. 8

pic. 5

pic. 6

TL7503BL

Tri-Liner, Blue, complete

TL76643RBLGE Wing-Holder, RH, Set of 3
TL7664RBLGE

Wing-Holder, RH

TL76643LBLGE

Wing-Holder, LH, Set of 3

TL7664LBLGE

Wing-Holder, LH

NA1

Nockadapter for Nockbed #1, Black

NA2

Nockadapter for Nockbed #2, Orange

TL7631RT

Tri-Liner, Tags, Red

TL99001

Tri-Liner, Ruler (Arm), Blue

TL99002

Tri-Liner, Segment (1/3), Blue

TL99003

Tri-Liner, Body, Blue

TL99004

Tri-Liner, Ring, Grey

TL99005

Tri-Liner, Cover, Blue

TL99006

Tri-Liner, Indicator, Red

TL99007

Tri-Liner, Screw

The Beiter Wing-Holder is designed to position and fletch 
vanes (e.g. Spin Wings™, Rite Flite™, Kurly Vanes™...) easily 
and precisely on arrow shafts.
It is available for Right-hand (RH) and Left-Hand (LH), 
and  for vane lenght 1-3/4" only.
The Beiter Wing-Holder comes with a Bushing, which 
allows off-set of the vane by 1°.

HOW TO PREPARE THE VANE
Clean the arrow shaft with acetone (before installing the nock!)
Draw the necessary lines with the Beiter Tri-Liner.
Insert the vane in the Beiter Wing-Holder (Pic.2) and align it with the edge as 
shown in Pic.3.
Strip off the first  layer of the tape as much as needed and hold it down  in one of 
the grooves on the back of the Beiter Wing-Holder. - Pic.4
Turn the Beiter Wing-Holder and position the tape along the edge of the vane. - 
Pic.5
Press on the tape. Than cut the useless parts of the tape on both sides with scissors 
or a knife. - Pic.6
Hint: Prepare more vanes ready to be fletched on more Wing-Holders and keep 
them safe in your quiver or bowcase. You will have one or more spare vanes ready 
to use! 

HOW TO FLETCH THE VANE
Strip off the second layer of the tape, so the fletching surface is free. 
Put the Beiter Wing-Holder on the arrow shaft, so that both pins are in contact 
with the shaft. Don't let the tape have contact with the shaft. 
Align the Beiter Wing-Holder along the drawn line, using the three positioning 
sectors placed along the vane edge. - Pic.7
Note: Place the vane in the correct  direction on the shaft, as shown on the Beiter 
Wing-Holder (Nock - Point) - Pic.1
Pay attention to place the vane along the drawn line and not on it! The tape won't 
hold on the line. Now press the Beiter Wing-Holder on the shaft.
Than release the pressure completely and turn away the shaft from the Beiter 
Wing-Holder. - Pic. 8