Panasonic KXMB2030SP Mode D’Emploi
Feature/Code
Selection
Setting recall/flash time
MBNM1NM2NM1N
(KX-MB2025/KX-MB2030
only)
MBNM1NM2NM1N
(KX-MB2025/KX-MB2030
only)
The recall/flash time depends on your telephone exchange or host PBX.
M0N “900ms”
M1N “700ms”
M2N “600ms”
M3N “400ms”
M4N “300ms”
M5N “250ms”
M6N “200ms”
M7N “160ms”
M8N “110ms”
M9N “100ms”
MGN “90ms”
MBN “80ms”
M0N “900ms”
M1N “700ms”
M2N “600ms”
M3N “400ms”
M4N “300ms”
M5N “250ms”
M6N “200ms”
M7N “160ms”
M8N “110ms”
M9N “100ms”
MGN “90ms”
MBN “80ms”
Note:
R The default may vary depending on the model.
R If the unit is connected via a PBX, PBX functions (transferring a call, etc.)
R The default may vary depending on the model.
R If the unit is connected via a PBX, PBX functions (transferring a call, etc.)
might not work correctly. Consult your PBX supplier for the correct setting.
Changing the LCD display
contrast
MBNM1NM4NM5N
contrast
MBNM1NM4NM5N
M1N “NORMAL” (default)
M2N “DARKER”
M2N “DARKER”
Selecting the scale
MBNM1NM4NM7N
MBNM1NM4NM7N
M1N “MILLIMETRES” (default)
M2N “INCHES”
M2N “INCHES”
Note:
R The selected scale will be used when measurements are shown on the
R The selected scale will be used when measurements are shown on the
unit’s display.
Changing the password for
feature programming via
remote operation
MBNM1NM5NM5N
feature programming via
remote operation
MBNM1NM5NM5N
1. MMenuN A MBNM1NM5NM5N A MSetN
2. Enter the current password. A MSetN
2. Enter the current password. A MSetN
R The default password is “1234”.
3. Enter a new 4-digit password using 0–9. A MSetN
4. Enter the new password again. A MSetN A MMenuN
4. Enter the new password again. A MSetN A MMenuN
Note:
R It is recommended that you change this password from the default
R It is recommended that you change this password from the default
password.
R This password is also used for feature programming via a web browser
(KX-MB2000/KX-MB2010/KX-MB2030, LAN connection only).
Setting the toner
maintenance time
MBNM1NM5NM8N
maintenance time
MBNM1NM5NM8N
The unit will automatically activate for maintenance, once every 24 hours.
Because this is to prevent the toner from solidifying, the noise that the unit
makes during maintenance cannot be stopped. However, if the unit’s noise
bothers you, you can change the start time.
1. MMenuN A MBNM1NM5NM8N A MSetN
2. Enter the maintenance start time.
Because this is to prevent the toner from solidifying, the noise that the unit
makes during maintenance cannot be stopped. However, if the unit’s noise
bothers you, you can change the start time.
1. MMenuN A MBNM1NM5NM8N A MSetN
2. Enter the maintenance start time.
R The default time is “12:00”.
R If you selected 12-hour time entry (page 22), press MHN repeatedly to
R If you selected 12-hour time entry (page 22), press MHN repeatedly to
select AM or PM.
R If you selected 24-hour time entry (page 22), the time is set using 24-hour
time entry.
3. MSetN A MMenuN
61
8. Programmable Features