Panasonic DMREX88 Mode D’Emploi

RQT9078

On the Unit’s Display

Page

H , F
(“ ” stands for a service number.)

 An error has occurred. The number following “H” or “F” depends on the status

of the unit. Check the items below and in the Troubleshooting Guide. If the
service number still does not disappear after the check, reset the unit (

86,

“To restore the unit if it freezes”).

−

 If the service numbers fail to clear, note the service numbers and contact a

qualified service person.

−

DVD
(“ ” stands for a number.)

 The remote control and the main unit are using different codes. Change the

code on the remote control.

GUIDE

 GUIDE Plus+ data is being downloaded.

HARD ERR



 If there is no change after turning the unit on and off, consult the dealer

where the unit was purchased.

−

NoERAS

 You cannot delete items on this disc.

The disc may be damaged. Use a new disc.

−

NoREAD

 The disc is dirty or badly scratched. The unit cannot record, play, or edit.

 The disc may be incompatible or of poor quality.

15, 16

 You have used a lens cleaner and it has finished operation. Press

[

 OPEN/CLOSE] on the main unit to eject the disc.

NoWRIT

 You cannot write to this disc.

The disc may be damaged. Use a new disc.

−

FINAL

 When the screen asking if you want to finalise the disc appears, the

message is displayed.

PLEASE WAIT



 Displayed when the unit is started. This is not a malfunction.

−

 The unit is carrying out its recovery process. You cannot operate the unit

while the message is displayed.

−

PROG FULL



 There are already 32 timer recording programmes. Delete unnecessary

timer recording programmes.

REMOVE

 The USB device is drawing too much power. Remove the USB device.

−

SP 35:50, LP 151h
“SP”, ”LP” and the numbers are
examples.

 Available space on the HDD or disc.

The example “SP 35:50” is displayed when less than 100 hours are available and
the example “LP 151h” is displayed when over 100 hours are available.
“SP” and “LP” are recording modes, “35:50” means “35 hours 50 minutes”
and “151h” means “151 hours”.

−

SW-DL

 The unit is performing a software update.

UNSUPPORT



 You have inserted a disc the unit cannot play or record onto.

15, 16

You tried to operate with a non-compatible USB memory.

UNFORMAT



 You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or

DVD-RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted.

F74

 The HDMI connection could not be authenticated due to a transfer

malfunction. Consult the dealer where the unit was purchased.

−

F75

 The HDMI connection could not be authenticated due to an internal data

malfunction. Consult the dealer where the unit was purchased.

−

U59

 The unit is hot.

The unit switches to standby for safety reasons. Wait for about 30 minutes
until the message disappears.
Select a position with good ventilation when installing the unit. Do not block
the cooling fan on the rear of the unit.

−

U61

 (When a disc is not inserted) Displays when a malfunction has occurred

during recording, playback or copy. This is displayed when the unit is in the
recovery process to return to normal operation; it is not broken. Once the
display disappears you can use the unit again.

−

U76

 HDMI cannot be output because you are connected to a model that does

not support copyright protection.

−

U80, U81, U99

 The unit fails to operate properly. Press [/I] on the main unit to switch the

unit to standby mode. Press [

/I] on the main unit again to turn the unit on.

−



The message are alternately displayed.

Messages

DMR-EX78_88EB.indb 84

2008/02/14 12:20:00