Panasonic NVMD10000GC Mode D’Emploi
Before using
52
VQT0S76
ª
Attaching the microphone to the movie camera
1
Attach the microphone to the movie camera shoe.
1) Loosen the shoe lock.
2) Attach the microphone.
3) Firmily tighten the shoe lock.
2) Attach the microphone.
3) Firmily tighten the shoe lock.
2
Connect the stereo mini-plug cord to the [EXT MIC]
socket.
socket.
≥You can adjust the microphone angle within the range shown
in the figure.
≥Hold the shoe lock portion when attaching and removing the
microphone.
≥Be sure to set the movie camera power to [OFF] before
connecting the microphone.
ª
Using the external stereo microphone
1
Set the [OFF/MONO/STEREO] switch to [MONO] or
[STEREO].
[STEREO].
[OFF]:
Turn off the microphone power.
[MONO]:
Records sound in front of the movie camera in
monaural.
monaural.
[STEREO]: Records sound in a wide area in stereo.
≥Although you can change the setting of the [OFF/MONO/
≥Although you can change the setting of the [OFF/MONO/
STEREO] switch while recording, the sound of the switch
being changed may be recorded. Pause your recording
before changing the setting of this switch.
being changed may be recorded. Pause your recording
before changing the setting of this switch.
≥When the [OFF/MONO/STEREO] switch is changed from
[OFF] to [MONO] or [STEREO], the [BATTERY] lamp will light
temporarily if there is still plenty of power in the battery. If the
[BATTERY] lamp does not light temporarily, replace the
battery with a new one.
temporarily if there is still plenty of power in the battery. If the
[BATTERY] lamp does not light temporarily, replace the
battery with a new one.
≥You can adjust the microphone sensitivity for recording. (
)
ª
Changing the [WIND CUT OFF/ON] switch
The microphone is equipped with a wind shield that is designed
to cut down wind noise, but when the wind is so strong that
even the wind shield is not adequate to keep down the noise,
set the [WIND CUT OFF/ON] switch to [ON] to further reduce
the wind noise.
[OFF]: The microphone should usually be used with this
to cut down wind noise, but when the wind is so strong that
even the wind shield is not adequate to keep down the noise,
set the [WIND CUT OFF/ON] switch to [ON] to further reduce
the wind noise.
[OFF]: The microphone should usually be used with this
position.
[ON]:
Set the [WIND CUT OFF/ON] switch to this position to
reduce wind noise or bass noise.
reduce wind noise or bass noise.
≥Although you can change the setting of the [WIND CUT OFF/
ON] switch while recording, the sound of the switch being
changed may be recorded. Pause your recording before
changing the setting of this switch.
changed may be recorded. Pause your recording before
changing the setting of this switch.
ª
About External Stereo Microphone
≥Do not expose the microphone to insecticides or volatile
substances.
≥Do not store the microphone in hot (approcimately 60 oC or
more) or humid (apporoximately 80% or more) places. In
particular, do not leave the microphone inside a car in mid
summer or near heating equipment.
particular, do not leave the microphone inside a car in mid
summer or near heating equipment.
≥A dirty plug may result in faulty contact. Be sure to wipe the
plug clean before connecting the microphone.
≥Do not connect or disconnect the stereo mini-plug with the
movie camera turned on.
≥Do not use a Ni-Cd battery.
1)
3)
2)
EXT MIC
OFF
STEREO
MONO
BATTERY
OFF ON
WIND CUT
VQT0S76_Eng.book 52 ページ 2005年7月21日 木曜日 午前11時48分