JL Audio MX650-CCX-SG-WH Manuel Du Propriétaire
6 | JL Audio - MX650-CCX / MX770-CCX Owner’s Manual
7
CoaXIal InstallatIon ProCeDure
DiagramsA&B(page7)showtypical
installation procedures into a fiberglass panel,
using the supplied hardware. Always follow proper
safety procedures. Use eye-protection at all times
and a dust mask and gloves when cutting.
using the supplied hardware. Always follow proper
safety procedures. Use eye-protection at all times
and a dust mask and gloves when cutting.
1) Choose a flat mounting surface that has
sufficient depth and air space behind it to
accept the speaker.
accept the speaker.
2) Using a hole saw or jigsaw, cut a mounting
hole for your respective speaker model (see
“Mounting Hole Diameter (E)” specifications,
page 2). If using a jigsaw, tracing the supplied
mounting template will provide you with an
accurate line on which to cut.
“Mounting Hole Diameter (E)” specifications,
page 2). If using a jigsaw, tracing the supplied
mounting template will provide you with an
accurate line on which to cut.
3) Run the speaker cable from the amplifier
output to the mounting location.
4) Place the speaker in the hole (or use the
mounting template) and mark the screw
hole locations using a sharp, pointed tool.
hole locations using a sharp, pointed tool.
5) Remove the speaker and drill a pilot hole (see
Pilot Hole Recommendation chart,
page7)ineachofthescrewlocations.
It is also advisable to use a hand-driven
countersink tool on each hole to further
inhibit gel-coat cracking of fiberglass panels.
page7)ineachofthescrewlocations.
It is also advisable to use a hand-driven
countersink tool on each hole to further
inhibit gel-coat cracking of fiberglass panels.
6) Connect the speaker wires from the
amplifier to the woofer connections.
SeeWiringDiagramonpage5.
SeeWiringDiagramonpage5.
7) Place the speaker into the opening.
8)Whileholdingthespeakerfirmlyinits
mounting location, place the #8 x 1 1/8-inch
Phillips pan-head mounting screws (with
washers) and snug in a criss-cross pattern,
then tighten with a hand screwdriver in a
criss-cross pattern.
Phillips pan-head mounting screws (with
washers) and snug in a criss-cross pattern,
then tighten with a hand screwdriver in a
criss-cross pattern.
Non-standard installations may require different
hardware. Always use marine-grade, stainless-steel
fasteners to ensure a secure, reliable installation.
fasteners to ensure a secure, reliable installation.
DIaGram a
DIaGram B
Fiberglass thickness
recommended Pilot Hole Drill size
0.312 in. (7.92 mm) or less
1/8 in. (3.18 mm) pilot hole
foam core / fiberglass sandwich
1/8 in. (3.18 mm) pilot hole
larger than 0.312 in. (7.92 mm)
9/64 in. (3.57 mm) pilot hole
#8 sCrew: PIlot Hole reCommenDatIons
InstallInG tHe sPeaKers
Once the mounting locations have been
established, run speaker cables from the amplifier
outputs to the mounting locations. If you are
running cables through bulkheads, drill holes for
the cable and use a urethane or plastic grommet
to protect the wire from chafing in the hole. Make
sure that the cables will clear any mechanical
devices in the boat and secure them with wire ties.
outputs to the mounting locations. If you are
running cables through bulkheads, drill holes for
the cable and use a urethane or plastic grommet
to protect the wire from chafing in the hole. Make
sure that the cables will clear any mechanical
devices in the boat and secure them with wire ties.
If you have any questions about the installation
or setup of your coaxial speaker system not
covered in this manual, please contact your
covered in this manual, please contact your
dealer or technical support.
Jl audio technical support:
(954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
Monday - Friday
Do not attempt to remove the tweeter from the grille or the grille from the speaker!
The tweeter is permanently fixed to the grille and its wiring is permanently attached to the speaker
frame. Attempting to remove the grille or the tweeter will damage the speaker and this damage will
not be covered under warranty.