SOLEM TBOS2FTUS1 Manuel D’Utilisation
STATEMENT
RF EXPOSURE
This device complies with FCC RF and Industry Canada
radiation exposure limits set forth for general population.
This device must be installed to provide a separation
distance of at least 20cm from all persons and must not
be co‐located or operating in conjunction with any other
antenna or transmitter.
radiation exposure limits set forth for general population.
This device must be installed to provide a separation
distance of at least 20cm from all persons and must not
be co‐located or operating in conjunction with any other
antenna or transmitter.
FCC STATEMENT
The user’s manual or instruction manual for an intentional
or unintentional radiator shall caution the user that
changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct
interference by one or more of the following measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and
receiver.
‐ Connect the equipment into an outlet on circuit different
from that to which the receiver is connected.
‐ Consult the dealer or an experienced radio/TV technician
for help.
Labeling requirements.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
or unintentional radiator shall caution the user that
changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct
interference by one or more of the following measures:
‐ Reorient or relocate the receiving antenna.
‐ Increase the separation between the equipment and
receiver.
‐ Connect the equipment into an outlet on circuit different
from that to which the receiver is connected.
‐ Consult the dealer or an experienced radio/TV technician
for help.
Labeling requirements.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2)
this device must accept any interference received,
including interference that may cause undesired
operation.
IC STATEMENT
RSS Gen / Transmitter Antenna.
Under Industry Canada regulations, this radio transmitter
may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Canada, le
présent émetteur radio peut fonctionner avec une antenne
d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de
réduire les risques de brouillage radioélectrique à
Under Industry Canada regulations, this radio transmitter
may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful
communication.
Conformément à la réglementation d'Industrie Canada, le
présent émetteur radio peut fonctionner avec une antenne
d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de
réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication
satisfaisante.
RSS Gen / User Manual Notice for Licence‐Exempt Radio
Apparatus.
This device complies with Industry Canada license‐exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes :(1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication
satisfaisante.
RSS Gen / User Manual Notice for Licence‐Exempt Radio
Apparatus.
This device complies with Industry Canada license‐exempt
RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and
(2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes :(1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
RADIO
Conformément à la réglementation d'Industrie Canada, le
présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur)
approuvé pour l'émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication
satisfaisante.
présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur)
approuvé pour l'émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication
satisfaisante.
NORMES CEM (radio)
CE
‐
‐
ETSI EN 300220-(V2.3.1-2010/02) and ETSI EN 300220-1
(V2.3.1-2010/02)
- EN 50371 (2002)
‐ ETSI EN 301 489‐1 (V1.8.1‐2008/4) et ETSI EN 301 489‐3
(V1.4.1‐2002108)
CANADA
‐ RSS‐210 Issue 7‐ Jun 2007 ‐ RSS‐Gen Issue 2‐ Jun 2007
FCC
‐ FCC Part 15, Subpart C 15.247
‐ ANSI C63.4 (2009)
‐ ETSI EN 301 489‐1 (V1.8.1‐2008/4) et ETSI EN 301 489‐3
(V1.4.1‐2002108)
CANADA
‐ RSS‐210 Issue 7‐ Jun 2007 ‐ RSS‐Gen Issue 2‐ Jun 2007
FCC
‐ FCC Part 15, Subpart C 15.247
‐ ANSI C63.4 (2009)
DÉCLARATION DE CONFORMITÉ
FR
‐
Etanchéité IP44
EN ‐
IP44 sealing
ES ‐
Estanquiedad IP68
Conformément à la Directive Européenne 2002/96/CE et à
la norme EN50419:2005, cet équipement ne
doit pas être jeté avec les ordures
ménagères.
Il doit faire l’objet d’une collecte sélective
appropriée
doit pas être jeté avec les ordures
ménagères.
Il doit faire l’objet d’une collecte sélective
appropriée
afin
de
permettre
sa
valorisation. Par ce geste, vous contribuerez
au respect de l’environnement et à la protection des
ressources naturelles.
ressources naturelles.