Mikrotikls SIA RB912G-5HPNDM Manuel D’Utilisation
See www.routerboard.com for more information. Contact support@mikrotik.com for support questions.
21-Aug-13
RouterBOARD
912G-‐5HPnD
Quick
Setup
Guide
and
Warranty
Information
RB912G
is
a
dual
chain
5GHz
802.11n
wireless
device
with
a
Gigabit
Ethernet port. Two models are available with 5GHz wireless: RB912UAG-‐
5HPnD (miniPCIe, SIM slot for 3G, USB 2.0 port, 64MB RAM), and
RB911G-‐5HPnD (32MB RAM, no SIM, no USB, no MiniPCIe).
Ethernet port. Two models are available with 5GHz wireless: RB912UAG-‐
5HPnD (miniPCIe, SIM slot for 3G, USB 2.0 port, 64MB RAM), and
RB911G-‐5HPnD (32MB RAM, no SIM, no USB, no MiniPCIe).
First
use
•
Connect
antenna
cables
to
the
built
in
Wi-‐Fi
connectors
•
Device
accepts
8-‐30V
with
a
passive
PoE
powered
Ethernet
ca-‐
ble or with a power connector to the Power Jack
ble or with a power connector to the Power Jack
Powering
The
board
accepts
power
with
the
following
modes:
•
With
PoE
to
Ether1
port.
It
accepts
8-‐30V
DC
input
(at
the
board; higher voltage needed to compensate for power loss on
long cables; at least 18V suggested) from non-‐standard (pas-‐
sive) Power over Ethernet injectors (no power over data lines). The board does not work with IEEE802.3af compliant
48V power injectors.
board; higher voltage needed to compensate for power loss on
long cables; at least 18V suggested) from non-‐standard (pas-‐
sive) Power over Ethernet injectors (no power over data lines). The board does not work with IEEE802.3af compliant
48V power injectors.
•
Direct
input
to
the
power
jack
8-‐30V
Booting
process
RouterOS
is
the
operating
system
of
all
RouterBOARD
routers.
Please
see
detailed
configuration
guide
here:
http://wiki.mikrotik.com/wiki/Category:Manual#list
This
device
doesn't
come
fitted
with
a
Serial
Port
connector,
so
initial
connection
has
to
be
done
via
the
Ethernet
cable,
using
the MikroTik Winbox utility. Winbox should be used to connect to the default IP address of 192.168.88.1 with the username
admin and no password.
the MikroTik Winbox utility. Winbox should be used to connect to the default IP address of 192.168.88.1 with the username
admin and no password.
In
case
you
wish
to
boot
the
device
from
network,
for
example
to
use
MikroTik
Netinstall,
hold
the
RESET
button
of
the
de-‐
vice when starting it until the LED light turns off, and Groove will start to look for Netinstall servers.
vice when starting it until the LED light turns off, and Groove will start to look for Netinstall servers.
In
case
IP
connection
is
not
available,
Winbox
can
also
be
used
to
connect
to
the
MAC
address
of
the
device.
More
infor-‐
mation here:
mation here:
http://wiki.mikrotik.com/wiki/First_time_startup
Extension
Slots
and
Ports
•
One
Gigabit
Ethernet
port
(With
Auto
MDI/X
so
you
can
use
either
straight
or
cross-‐over
cables
for
connecting
to
other network devices). The Ethernet port accepts 8-‐30V DC powering from a passive PoE injector.
other network devices). The Ethernet port accepts 8-‐30V DC powering from a passive PoE injector.
•
Built-‐in
802.a/n
WiFi
card
(AR9342)
with
two
MMCX
connectors
•
Only
RB912UAG-‐5HPnD:
miniPCI-‐e
slot
for
either
a
802.11
Wireless
card,
or
a
3G
modem
(when
a
3G
modem
is
used in miniPCIe slot, USB port will become inactive. In RouterOS you can select which of the 3G modems you want
to use, USB or miniPCIe). SIM slot is available for miniPCIe 3G cards.
used in miniPCIe slot, USB port will become inactive. In RouterOS you can select which of the 3G modems you want
to use, USB or miniPCIe). SIM slot is available for miniPCIe 3G cards.
•
Only
RB912UAG-‐5HPnD:
USB
2.0
port