Shenzhen Gospell Smarthome Electronic Co. Ltd. Y5703 Manuel D’Utilisation

   Model: Y5703GAA

Before using the product, please read the guide carefully to avoid
any damages to the product in virtue of faulty operation or misuse.

-03-

※All parameters change without prior notice, The finial right of 
     interpretation is reserved by the company.

-04-

-07-

-06-

 

2. In setting page of app (Fig. 11), click “Delete device” to 
   remove the connected camera, can remove the bonding 
   with the account. 

6. Push message: when movement is detected, alarm message 
   can be sent to server and pushed to your phone.

1. Suggest using qualified micro-SD card to avoid 
   incompatibility. Format micro-SD card before using.

5. Cancel"sharing with friends": Delete the camera and cancel
    "sharing with friends". (You have to re-add the camera to 
    use it again) 

8.Only support the special characters in English mode,
   such as: " @, #, &, *,    ~, ｛, ｝, -, =, +, /, ?, (, )", 
Dont support the special characters, such as:"%", "\", "<>". 

-08-

(1)this device may not cause harmful interference, and 
(2) this device must accept any interference received, including 
interference that may cause undesired operation.
The Maximum Permissible Exposure (MPE) level has been calculated 
based on a distance of d=20 cm between the device and the human body. 
To maintain compliance with RF exposure requirement, use product that 
maintain a 20cm distance between the device and human body. Hereby, 
we declares that this device is in compliance with the essential 
requirements and other relevant provisions of Directive 2014/53/EU.
Notice: Observe the national local regulations in the location where the 
device is to be used. This device may be restricted for use in some or all 
member states of the European Union (EU).

- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to 
   which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party 
responsible for compliance could void the user's authority to operate the 
equipment. 
This device complies with Part 15 of the FCC Rules. Operation is subject 
to the following two conditions:

Note: This equipment has been tested and found to comply with the 
limits for a Class B digital device, pursuant to part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against 
harmful interference in a residential installation. This equipment 
generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause 
harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If 
this equipment does cause harmful interference to radio or television 
reception, which can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by one or more 
of the following measures:

-02-

1. 2.4G wireless router is required. 
2. Support Android 4.4 and above, iOS 8.0 and above

     

3. Download APP: Scan the QR code below and complete the 
    installation

4. Add a device: Open the APP home page.click the “Add Device” 
    icon to connect your camera. According to the settings guide 
    in the APP, you can configure multiple cameras at the same 
    time.

1. Find the power interface behind the product and power on the 
    camera,The indicator will turn on.
2. Please make sure there is WiFi available.

-05-

-01-

7. Remote monitoring: after the camera is connected to Internet 
   successfully, you can monitor your home anywhere ,anytime.

4. Sharing with Friends: Share  your QR code to your friends. 

3. Movement detection: when movement is detected within 
   the scope of camera, the camera will record video and take 
   photos automatically. Videos and photos will be saved in 
   micro-SD card.

Indicates that power failure or network 
not connected.

Red indicator 
remains

Red indicator 
flashes

Indicates that camera is connecting to 
network.

Green indicator 

flashes

Indicates the router connected 
successfully (no Internet).

Green indicator 
remains

Indicates the camera is connected to 
server and working well.

    
         
    d)   Ensure that SSID and password are no longer than 16 
         characters
    e)   Ensure that SSID is broadcasted.
    f )   Ensure that the DHCP is enabled on router.
    g)   Ensure that Wi-Fi encryption method is WPA2-PSK/
         WPA-PSK or AES.
    h)   Ensure that Wi-Fi signal is 2.4GHz.
    i )   Ensure that there is no MAC filter on router or add 
         MAC address to router whitelist
     j )   We suggest rebooting the router, and the "security 
         settings, encryption method" of WiFi password should 
         never choose "auto-select".
    k )   Reset the camera to set up connection again. Press 
         and hold SET key for 5 seconds. 
2. Red indicator remains, network connection is failed.
    a)  Ensure that the password of Wi-Fi is correct.
    b)  Ensure that the network connects to Internet freely.
    c)  Ensure that the camera is in range of Wi-Fi hotspot.
3. Green indicator flashes, connection to server failed.
    a)  Ensure that Wi-Fi signal is strong enough and 
         bandwidth is enough for connection. Move near to 
         Wi-Fi hotspot or increase the bandwidth.
    b)  Ensure that camera is not under interferon of other 
         2.4GHz signal.

    b)   Ensure that camera is in range of router. Keep the 
         distance less than 40fts between router and indoor 
         camera, less than 65fts for outdoor camera.
    
         

c)   Ensure that SSID and password of Wi-Fi contains no 
     special characters. Modify the SSID and password of
     Wi-Fi with only English characters, no special characters. 

1.  Wi-Fi cannot be connected
    a)   Ensure that the antenna of camera is fixed well.

Imaging sensor

Effective pixel

Horizontal viewing angle

Wireless transmission way

Transmission Range

Interface

Remote monitor

1/4",CMOS

100W pixels

85±5°

WiFi

Indoor: 20m 
Set Button

Support Android and IOS

Power supply

5V 1A,

 DC

 Screws   

Power adapter 

USB cable

 ※ The picture is only for reference and the real object shall prevail

 Camera 

 User manual 

   Model: T5703GAB

Before using the product, please read the guide carefully to avoid
any damages to the product in virtue of faulty operation or misuse.

Light sensor 

Camera lens

LED indicating lamp

Set button

Base

MIC hole

USB port

Loudspeaker

正面

反面

IOS

Android

Micro USB