Tivoli Audio NETWORKS Manuel D’Utilisation
3
“Settings” menu using the pq buttons and the Select button to set the hour. Repeat to
set the minutes and press Select to save. Within this same “Settings” menu are additional
options to set the date, clock format (time shown as digits or as a clock face in Off mode),
/4 hour mode, and Daylight Savings Time (adjusted automatically when DST occurs).
set the minutes and press Select to save. Within this same “Settings” menu are additional
options to set the date, clock format (time shown as digits or as a clock face in Off mode),
/4 hour mode, and Daylight Savings Time (adjusted automatically when DST occurs).
Language (found under “Settings”): Use the pq buttons and Select button to choose your
language.
language.
Factory Re-Set (found under “Settings”): Use the pq buttons and the Select button
to initiate a factory re-set. If you choose Yes, a message will ask you to confirm this choice.
A factory re-set will erase all presets, language selection, Favorites, date, clock, alarm, WiFi
security password (if applicable), EQ settings, and any other customized settings.
to initiate a factory re-set. If you choose Yes, a message will ask you to confirm this choice.
A factory re-set will erase all presets, language selection, Favorites, date, clock, alarm, WiFi
security password (if applicable), EQ settings, and any other customized settings.
Info (found under “Settings”): This shows information about your NetWorks+ radio which
you might be asked to provide should you phone or email with questions about software or
repair. This differs from the Info button on the remote control.
you might be asked to provide should you phone or email with questions about software or
repair. This differs from the Info button on the remote control.
Software Upgrade (found in the main menu under “IR Setup” in Internet radio mode
only): A message will appear automatically in Internet radio mode advising you when new
firmware is available. Select Yes to begin the download, or No (or the left arrow/back button)
to download at another time. The upgrade process typically takes a few minutes to complete
and a progress bar will show the status of the upgrade. There will be no audio output during
this process. The Networks+ will automatically re-boot after a successful upgrade. To check
to see if an upgrade is available, access the “IR Setup” in the main menu in Internet radio
mode and select “Software Upgrade”. It is recommended you check for a software upgrade
after completing initial set-up of your NetWorks+ to be sure its software is fully up-to-date.
Several different upgrades might be necessary.
WARNING: It is vital the NetWorks+ not be powered off or unplugged during the
software upgrade process or else the radio will require servicing to restore operation
only): A message will appear automatically in Internet radio mode advising you when new
firmware is available. Select Yes to begin the download, or No (or the left arrow/back button)
to download at another time. The upgrade process typically takes a few minutes to complete
and a progress bar will show the status of the upgrade. There will be no audio output during
this process. The Networks+ will automatically re-boot after a successful upgrade. To check
to see if an upgrade is available, access the “IR Setup” in the main menu in Internet radio
mode and select “Software Upgrade”. It is recommended you check for a software upgrade
after completing initial set-up of your NetWorks+ to be sure its software is fully up-to-date.
Several different upgrades might be necessary.
WARNING: It is vital the NetWorks+ not be powered off or unplugged during the
software upgrade process or else the radio will require servicing to restore operation
How to use the Alarm and Sleep timer and other functions specific
to the remote control:
to the remote control:
The remote control duplicates the controls found on the rear of NetWorks+ but adds these
additional dedicated commands for your convenience:
additional dedicated commands for your convenience:
Alarm: Using the pq buttons and Select button, select Alarm or . Set the alarm wake
time hour and press select to move to the minutes. Press select when done. Alarm bell icons
with a “” and “” next to them will be shown on the display when the respective alarms are
set to wake.
time hour and press select to move to the minutes. Press select when done. Alarm bell icons
with a “” and “” next to them will be shown on the display when the respective alarms are
set to wake.
After the alarm time is set, set the source and volume level you wish to wake to. If you wish
to wake to an Internet or FM station, be sure the station is broadcasting during the time the
alarm is set to activate. Finally, set the alarm to wake or keep it off.
to wake to an Internet or FM station, be sure the station is broadcasting during the time the
alarm is set to activate. Finally, set the alarm to wake or keep it off.
During a power outage, the alarm time(s) will be maintained by an integrated back-up.
However, if power is lost during the time the alarm is set to activate, the alarm will wake
using a tone, regardless of what alarm source was selected.
However, if power is lost during the time the alarm is set to activate, the alarm will wake
using a tone, regardless of what alarm source was selected.
If waking to an Internet radio station that is unavailable or takes too long to load, the
alarm will default to the tone as a back-up.
alarm will default to the tone as a back-up.
When the alarm sounds in any source but the tone you have three options: () press the
Snooze button to mute the alarm for 7 minutes; () press the power button to turn the
Snooze button to mute the alarm for 7 minutes; () press the power button to turn the
8.
9.
10.
11.
1.