Eleven Engineering Inc. PL5554 Manuel D’Utilisation
SKAA User’s Manual
For all SKAA part numbers including PL5553, PL5554 and PL5556
SKAA
TM
transmitters each support up to four SKAA receiver units at the same time. The SKAA logo
guarantees compatibility
between transmitters and receivers.
Green List ‐ All SKAA receivers have a Green List which is just a list of your favorite transmitters. The first time you use a receiver, the
Green List is empty, so you need to Double Click the SKAA button to hunt for a new transmitter. If your receiver consists of two or
more wireless units, (for example, a left speaker and a right speaker) we call that a Cluster. The unit with the SKAA button is the
Master of the Cluster and it is where the Green List is kept. Each unit uses three LED colors to communicate SKAA status: green,
amber and red.
Green List is empty, so you need to Double Click the SKAA button to hunt for a new transmitter. If your receiver consists of two or
more wireless units, (for example, a left speaker and a right speaker) we call that a Cluster. The unit with the SKAA button is the
Master of the Cluster and it is where the Green List is kept. Each unit uses three LED colors to communicate SKAA status: green,
amber and red.
SKAA
TM
is a trademark of Eleven Engineering Incorporated. Please visit
Common SKAA Commands
Command
Button
LED
Hunt through Green List (look for favorite
transmitters)
transmitters)
Single Click
Hunting
(Flash) Green List #
Bonded
(Flash) Green List #
Bonded
Explore; hunt for new transmitters
Double Click
Hunting
Bonded
Bonded
Add / delete transmitter from Green List
Hold for 3 seconds
Æ Added
(Flash) Deleted
Automatically add transmitter to Green List by
listening continuously for 30 minutes.
listening continuously for 30 minutes.
‐
Æ Added
More SKAA Commands
Command
Button
LED
When hunting through green list, stop at the
current green list entry and continue to look solely
for that transmitter
current green list entry and continue to look solely
for that transmitter
Single Click
Hunting
(Flash) Green List #
Bonded
(Flash) Green List #
Bonded
Mute
Triple Click
Flashing
If muted, unmute
Single Click
Returns to previous
Erase the Green List; start over
Click 6 times
Flashes
To make a Cluster of receivers:
1. power on Master while holding down SKAA
button (hold button until red LED starts
flashing)
flashing)
2. power on remaining receiver units
3. once LED on Master becomes solid (stops
3. once LED on Master becomes solid (stops
flashing), turn off the Master and all other
receiver units
receiver units
Hold during power on.
Note ‐ only receiver units
from the same manufacturer
and product family may
become a Cluster
from the same manufacturer
and product family may
become a Cluster
(Flashing) Master has
entered cluster up
mode
Cluster has been
successfully made
entered cluster up
mode
Cluster has been
successfully made
FCC Statement:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
IC Statement
This Class B digital apparatus complies with Canadian ICES-003.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Cet appareil numérique de la classe B est conforme á la norme NMB-003 du Canada.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.