Cellink Co. Ltd. 4710874200036 Manuel D’Utilisation
RF COMBO 1
BATTERY INSTALLATION
Mouse
1. As shown as fig.1 to fig.4, please hold the mouse and press the center part of the
two keys with one thumb. Meanwhile, with the other hand, pull the top cap backward
and open it.
2. Put two AAA alkaline batteries according to its direction. Then, put back the top cap
(as shown as fig.3) aiming at and along with the waist of the mouse.
Caution:
When battery power is low, the mouse pattern will show red color on the
right-down corner of window screen for warning.
Keyboard
Open the battery cap, which is on keyboard's reverse side, place 4 pieces AAA Alkaline
BATTERY INSTALLATION
Mouse
1. As shown as fig.1 to fig.4, please hold the mouse and press the center part of the
two keys with one thumb. Meanwhile, with the other hand, pull the top cap backward
and open it.
2. Put two AAA alkaline batteries according to its direction. Then, put back the top cap
(as shown as fig.3) aiming at and along with the waist of the mouse.
Caution:
When battery power is low, the mouse pattern will show red color on the
right-down corner of window screen for warning.
Keyboard
Open the battery cap, which is on keyboard's reverse side, place 4 pieces AAA Alkaline
batteries,
and put the cap back.
Every time after having changed batteries, please reset up the mouse
according to the steps of " SETUP FOR USE".
HARDWARE INSTALLATION
1. Shut down the power of the computer. (Caution: Do not plug in or out USB or PS/2
connector port when the power of the computer is still on, otherwise will damage
the computer.)
2. Connect the green connector of the receiver (according to the type you
have bought) to the PS/2 connection port of the computer, or connect the white
connector to the USB connection port on the computer.
3. Turn on the computer.
SOFTWARE INSTALLATION (DRIVE PROGRAM)
1. Insert the CD / Driver into Drive -D (In case the CD-ROM is in D-drive).
2. Get into "execution" on window screen. Click twice on the file of
"setup exe" in D-drive of the CD to proceed setup, and follow the
steps indicated in the screen to complete the setup.
3. After the setup has been completed, the screen will restart automatically.
And, it will show a mouse pattern on the right-down corner of the screen.
Caution: When it is in PS/2 mode, this driver doesn't support "Low battery display".
SETUP FOR USE
1. MOUSE:
Aim the front point of the mouse at receiver.
PRESS FIRST THE BUTTON ON THE REVERSE SIDE OF MOUSE, THEN PRESS THE
CONNECTOR BUTTON ON THE RECEIVER. (NEVER DO THE CONTRARY WAY.)
The LED lights of the mouse and keyboard will light up. When mouse LED light goes
off ,
it means the setup of the mouse is completed.
2. KEYBOARD:
PRESS THE BUTTON ON THE REVERSE SIDE OF KEYBOARD. When the LED light
of keyboard goes off, it means the setup of the keyboard is completed as well. And
you may start to work with this RF Combo device.
3. The setup must be completed in one minute. If exceeded, please repeat the steps.
MOUSE BUTTON FUNCTION SETUP
Every time after having changed batteries, please reset up the mouse
according to the steps of " SETUP FOR USE".
HARDWARE INSTALLATION
1. Shut down the power of the computer. (Caution: Do not plug in or out USB or PS/2
connector port when the power of the computer is still on, otherwise will damage
the computer.)
2. Connect the green connector of the receiver (according to the type you
have bought) to the PS/2 connection port of the computer, or connect the white
connector to the USB connection port on the computer.
3. Turn on the computer.
SOFTWARE INSTALLATION (DRIVE PROGRAM)
1. Insert the CD / Driver into Drive -D (In case the CD-ROM is in D-drive).
2. Get into "execution" on window screen. Click twice on the file of
"setup exe" in D-drive of the CD to proceed setup, and follow the
steps indicated in the screen to complete the setup.
3. After the setup has been completed, the screen will restart automatically.
And, it will show a mouse pattern on the right-down corner of the screen.
Caution: When it is in PS/2 mode, this driver doesn't support "Low battery display".
SETUP FOR USE
1. MOUSE:
Aim the front point of the mouse at receiver.
PRESS FIRST THE BUTTON ON THE REVERSE SIDE OF MOUSE, THEN PRESS THE
CONNECTOR BUTTON ON THE RECEIVER. (NEVER DO THE CONTRARY WAY.)
The LED lights of the mouse and keyboard will light up. When mouse LED light goes
off ,
it means the setup of the mouse is completed.
2. KEYBOARD:
PRESS THE BUTTON ON THE REVERSE SIDE OF KEYBOARD. When the LED light
of keyboard goes off, it means the setup of the keyboard is completed as well. And
you may start to work with this RF Combo device.
3. The setup must be completed in one minute. If exceeded, please repeat the steps.
MOUSE BUTTON FUNCTION SETUP