All American Sports Corporation R63311 Manuel D’Utilisation
P/N R63314 v1.0
Page | 28
2)
Click the “TRANSFER” button on the middle right of the screen.
3)
Select the team you wish to transfer the Player Unit to and click 'OK'.
4)
Plug in an Alert Monitor assigned to the equipment’s new team and
follow the Player Unit Synchronization Wizard prompts to complete
the transfer process. If the Player Unit was assigned to a player, the
Alert Monitors for the previous team will also need to be
synchronized. To update new settings for the previous team,
connect that Alert Monitor and click the yellow “SYNC” button.
the transfer process. If the Player Unit was assigned to a player, the
Alert Monitors for the previous team will also need to be
synchronized. To update new settings for the previous team,
connect that Alert Monitor and click the yellow “SYNC” button.
5)
Manually Check-In the Player Unit after the transfer by holding down
the Check-In button on the Player Unit for 2 seconds until the red
Power button flashes on then off.
Power button flashes on then off.
Transferring an Alert Monitor
An Alert Monitor may be transferred between teams when one team has
two Alert Monitors and the other team only has one. A team must
always have at least one Alert Monitor.
two Alert Monitors and the other team only has one. A team must
always have at least one Alert Monitor.
To transfer an Alert Monitor from one team to another, perform the
following steps under the “EQUIPMENT ASSIGNMENTS” tab, “ALERT
MONITOR” submenu:
following steps under the “EQUIPMENT ASSIGNMENTS” tab, “ALERT
MONITOR” submenu:
1)
Find and select the Alert Monitor you wish to transfer.
2)
Click the “TRANSFER” button.
3)
Select the team you wish to transfer the Alert Monitor to and click
“OK”.
4)
All Alert Monitors on the current team and the new team will need to
be synchronized, including the recently transferred one (see
Creating Players and Assigning Player Units, Steps 6-8, p.25).
Creating Players and Assigning Player Units, Steps 6-8, p.25).
Deleting Players or Equipment
Players and equipment may be deleted in the “PLAYER SETUP” and
“EQUIPMENT ASSIGNMENTS” tabs, respectively. To do so:
“EQUIPMENT ASSIGNMENTS” tabs, respectively. To do so:
1)
Highlight the player or equipment you wish to delete, and click the
minus symbol icon.
P/N R63314 v1.0
Page | 29
2)
Sync Alert Monitors from all affected teams when prompted. (see
Creating Players and Assigning Player Units, Steps 6-8, p.25).
3)
Power down all deleted Player Units that will not be reassigned
within 24 hours to conserve battery life (see Player Unit Controls &
Indicators, p.13).
Indicators, p.13).
Note:
Note:
Note:
Note: InSite Player Management software requires at least one
Alert Monitor to be assigned to a team at all times. For teams with
a single Alert Monitor that must be replaced, add the second
replacement Alert Monitor to the team, Sync both Alert Monitors,
and Check-In all Player Units, before deleting the first.
Alert Monitor to be assigned to a team at all times. For teams with
a single Alert Monitor that must be replaced, add the second
replacement Alert Monitor to the team, Sync both Alert Monitors,
and Check-In all Player Units, before deleting the first.
System Settings
This screen allows the user to change various default settings and
manually update software.
manually update software.
1)
Team Name
Team Name
Team Name
Team Name - Allows the user to modify the Team name. The Team
name for the Alert Monitor that is currently connected to the
computer will be displayed.
name for the Alert Monitor that is currently connected to the
computer will be displayed.
2)
Edit / Save Changes
Edit / Save Changes
Edit / Save Changes
Edit / Save Changes - Click this button to edit the team name, and
again to save the changes. Alert Monitors must be synced to
acknowledge the changes.
again to save the changes. Alert Monitors must be synced to
acknowledge the changes.
3)
Delete Team
Delete Team
Delete Team
Delete Team - Click this button to delete the currently displayed
team.
team.