CipherLab Co. Ltd. 3656CRADLE Manuel D’Utilisation
107
Update
Chapter 3
錯誤
錯誤
錯誤
錯誤! ! ! ! 使用
使用
使用
使用 [[[[常用
常用
常用
常用] ] ] ] 索引標籤將
索引標籤將
索引標籤將
索引標籤將 Heading 1
Heading 1
Heading 1
Heading 1
套用到您想要在此處顯示的文字
套用到您想要在此處顯示的文字
套用到您想要在此處顯示的文字
套用到您想要在此處顯示的文字。
。
。
。
3.
3.
3.
3.1
1
1
1 CONNECTING VIA
CONNECTING VIA
CONNECTING VIA
CONNECTING VIA 3656
3656
3656
3656 CRADLE
CRADLE
CRADLE
CRADLE
By default, the interface of 3656 CRADLE is set to “USB HID”. Use the interface cable to
connect the scanner via 3656 CRADLE to PC. You can have up to seven scanners
connected to one computer at the same time.
connect the scanner via 3656 CRADLE to PC. You can have up to seven scanners
connected to one computer at the same time.
Note: If using USB Virtual COM for the first time, you must install its driver beforehand.
Driver version 5.4 or later is required. Please remove older versions!
3.
3.
3.
3.1
1
1
1.1 CONNECT TO
.1 CONNECT TO
.1 CONNECT TO
.1 CONNECT TO 3656
3656
3656
3656 CRADLE
CRADLE
CRADLE
CRADLE
By scanning two setting barcodes in sequence
By scanning two setting barcodes in sequence
By scanning two setting barcodes in sequence
By scanning two setting barcodes in sequence
Connect any scanner to 3656 CRADLE by reading the two labels at the back of 3656 CRADLE. The
scanner will respond with one beep upon reading each of the labels.
scanner will respond with one beep upon reading each of the labels.
“Set Connection” label
“Serial Number” label
After reading these labels, the scanner will stay active for a specified period of time (2 minutes by
default) trying to connect to the 3656 CRADLE while its LED is flashing blue (On/Off ratio 0.5 s: 0.5
s). Once connected, the scanner will respond with three beeps (tone ascending from low to high),
and the LED flashes blue (On/Off ratio 0.02 s: 3 s). When out of range, the scanner will respond
with three short beeps (tone descending from high to low).
default) trying to connect to the 3656 CRADLE while its LED is flashing blue (On/Off ratio 0.5 s: 0.5
s). Once connected, the scanner will respond with three beeps (tone ascending from low to high),
and the LED flashes blue (On/Off ratio 0.02 s: 3 s). When out of range, the scanner will respond
with three short beeps (tone descending from high to low).
Usage:
Read the “Set Connection” barcode first, and then the “Serial Number” barcode. If the “Set
Connection” barcode on 3656 CRADLE is illegible, try this one —
Connection” barcode on 3656 CRADLE is illegible, try this one —
Set Connection
Note: The 3656 CRADLE settings will overwrite the interface-related settings on the
scanners that are currently connected to 3656 CRADLE.
By scanning a single 1D setting barcode
By scanning a single 1D setting barcode
By scanning a single 1D setting barcode
By scanning a single 1D setting barcode
Users can produce a single 1D setup barcode that combines the “Set Connection” and “3656
CRADLE Serial Number” setup commands to connect with the target device. While producing the
barcode, be aware the letter upper/lower case “SeTcOn” and the barcode must be the Code 128
symbology.
CRADLE Serial Number” setup commands to connect with the target device. While producing the
barcode, be aware the letter upper/lower case “SeTcOn” and the barcode must be the Code 128
symbology.
Usage:
Read the “SeTcOnxxxxxxxxx” single 1D barcode. The scanner will respond with one beep
upon reading the barcode.
upon reading the barcode.