Linksys E8350 Manuel D’Utilisation

1

Wireless Regulatory Information

FCC Statement

This device complies with Part 15 of the FCC Rules . 

Operation is subject to the following two conditions: (1) 

This device may not cause harmful interference, and 

(2) this device must accept any interference received, 

including interference that may cause undesired 

operation .
This product has been tested and complies with the 

specifications for a Class B digital device, pursuant to 

Part 15 of the FCC Rules . These limits are designed 

to provide reasonable protection against harmful 

interference in a residential installation . This equipment 

generates, uses, and can radiate radio frequency 

energy and, if not installed and used according to the 

instructions, may cause harmful interference to radio 

communications . However, there is no guarantee that 

interference will not occur in a particular installation . If 

this equipment does cause harmful interference to radio 

or television reception, which is found by turning the 

equipment off and on, the user is encouraged to try to 

correct the interference by one or more of the following 

measures:

 • Reorient or relocate the receiving antenna
 • Increase the separation between the equipment and 

devices

 • Connect the equipment to an outlet other than the 

receiver’s

 • Consult a dealer or an experienced radio/TV technician 

for assistance

FCC Caution: Any changes or modifications not expressly 

approved by the party responsible for compliance could 

void the user’s authority to operate this equipment .
IEEE 802 .11b or 802 .11g operation of this product in 

the USA is firmware-limited to channels 1 through 11 .
The device for the band 5150-5250 MHz is only 

for indoor usage to reduce the potential for harmful 

interference to co-channel mobile satellite systems .

Mexico Regulatory Statement

La  operación de este equipo está sujeta a las siguientes 

dos condiciones: (1) es  posible que este equipo o 

dispositivo no cause interferencia perjudicial y (2)  este 

equipo o dispositivo debe aceptar cualquier interferencia, 

incluyendo la  que pueda causar su operación no deseada .

EAC Mark of Conformity for Russia, 

Kazakhstan and Belarus

FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure 

limits set forth for an uncontrolled environment . This 

equipment should be installed and operated with 

minimum distance 27 cm between the radiator and your 

body .
This device and it’s antennas(s) must not be co-

located or operating in conjunction with any other 

antenna or transmitter except in accordance 

with FCC multi-transmitter product procedures . 

 

Industry Canada Statement

CAN ICES-3 (B)/NMB-3 (B)
Operation is subject to the following two conditions: (1) 

This device may not cause interference, and (2) this device 

must accept any interference, including interference that 

may cause undesired operation of the device .
For product available in the USA/Canada market, only 

channel 1~11 can be operated . Selection of other 

channels is not possible .
The device could automatically discontinue transmission 

in case of absence of information to transmit, or 

operational failure . Note that this is not intended to prohibit 

transmission of control or signaling information or the 

use of repetitive codes where required by the technology . 

 

Industry Canada Radiation Exposure 

Statement

This equipment complies with IC radiation exposure limits 

set forth for an uncontrolled environment . This equipment 

should be installed and operated with minimum distance 

27 cm between the radiator & your body .
This device and it’s antennas(s) must not be co-located 

or operating in conjunction with any other antenna 

or transmitter except in accordance with IC multi-

transmitter product procedures .
 

Restrictions in the 5 GHz Band

The device for the band 5150-5250 MHz is only for 

indoor usage to reduce potential for harmful interference 

to co-channel mobile satellite systems .
This device has been designed to operate with an 

antenna having a maximum gain of 2 .5 dBi and 3 .8 dBi at  

2 .4 GHz and 5 GHz respectively . Antenna having a higher 

gain is strictly prohibited per regulations of Industry 

Canada . The required antenna impedance is 50 ohms .
The maximum antenna gain (Please see the table below) 

permitted (for devices in the bands 5250-5350 MHz 

and 5470-5725 MHz) to comply with the EIRP limit and 

because high power radars are allocated as primary users 

(meaning they have priority) in 5250-5350 MHz and