G-Way Microwave / G-Wave PS7W83790N Manuel D’Utilisation
4 |
P a g e
OVERVIEW
The BDA assembly enhances the coverage area of radio communications in buildings and RF
shielded environments.
The BDA has dual RF paths (Down-Link / Up-Link) to improve coverage in two distinct
frequency bands.
The unit features low noise figure and wide dynamic range. It is based on a dual duplexed
path configuration with sharp out of band attenuation allowing improved isolation between the
receive and transmit paths.
BDA-PS7W/PS8NEPS-37/37-90-N for USA market and BDA-PS7/PS8-37/37-90-N for
Canadian market, provides up to 37 dBm composite power and has up to 85db gain.
shielded environments.
The BDA has dual RF paths (Down-Link / Up-Link) to improve coverage in two distinct
frequency bands.
The unit features low noise figure and wide dynamic range. It is based on a dual duplexed
path configuration with sharp out of band attenuation allowing improved isolation between the
receive and transmit paths.
BDA-PS7W/PS8NEPS-37/37-90-N for USA market and BDA-PS7/PS8-37/37-90-N for
Canadian market, provides up to 37 dBm composite power and has up to 85db gain.
FCC NOTE
This is a Class B device. The product has been tested and found to comply with the Booster
requirements per FCC Part 90.
requirements per FCC Part 90.
IC NOTE
The product has been tested and found to comply with the Industry Canada (IC) RF Exposure
Requirements, pursuant to IC RSS-131.
Requirements, pursuant to IC RSS-131.
NOTE
The Manufacturer’s rated output power of this equipment is for single carrier operation. For
situations when multiple carrier signals are present, the rating would have to be reduced by
3.5 dB, especially where the output signal is re-radiated and can cause interference to
adjacent band users. This power reduction is to be by means of input power or gain reduction
and not by an attenuator at the output of the device.
situations when multiple carrier signals are present, the rating would have to be reduced by
3.5 dB, especially where the output signal is re-radiated and can cause interference to
adjacent band users. This power reduction is to be by means of input power or gain reduction
and not by an attenuator at the output of the device.
RF EXPOSURE WARNING-FCC
The ERP limit, as defined by the FCC is +37 dBm. In order to comply with the FCC RF exposure
requirements, the antenna installation must comply with the following:
An antenna with 8.5 dBi gain must be installed so as to provide a minimum separation distance of at
least 81.9 cm (~32.3 inches) between the antenna connected to the RF booster and the human user’s
body within the area. (This assumes an antenna with gain of 0 dBi, VSWR ≤ 2:1, Zo= 50 ohms and a
cable attenuation less then 1dB).
Should user choose to utilize a higher gain antenna (greater than 8.5 dBi ) with the system, attenuation
of the BDA’s gain will be required to meet FCC ERP limit of +37 dBm
requirements, the antenna installation must comply with the following:
An antenna with 8.5 dBi gain must be installed so as to provide a minimum separation distance of at
least 81.9 cm (~32.3 inches) between the antenna connected to the RF booster and the human user’s
body within the area. (This assumes an antenna with gain of 0 dBi, VSWR ≤ 2:1, Zo= 50 ohms and a
cable attenuation less then 1dB).
Should user choose to utilize a higher gain antenna (greater than 8.5 dBi ) with the system, attenuation
of the BDA’s gain will be required to meet FCC ERP limit of +37 dBm
RF EXPOSURE WARNING- INDUSTRY CANADA
In order to comply with the IC RF exposure requirements, the antenna installation must comply with the
following:
For 2 dBi gain antenna: The antenna must be installed so as to provide a minimum separation
distance of at least 32.5cm (~12.8 inches) between the antenna connected to the RF booster and the
human user’s body within the area. (VSWR ≤ 2:1, Zo= 50 ohms and a cable attenuation less then 1dB).
For 8.5 dBi gain antenna: The antenna must be installed so as to provide a minimum separation
distance of at least 68.7cm (~27.1 inches) between the antenna connected to the RF booster and the
human user’s body within the area
following:
For 2 dBi gain antenna: The antenna must be installed so as to provide a minimum separation
distance of at least 32.5cm (~12.8 inches) between the antenna connected to the RF booster and the
human user’s body within the area. (VSWR ≤ 2:1, Zo= 50 ohms and a cable attenuation less then 1dB).
For 8.5 dBi gain antenna: The antenna must be installed so as to provide a minimum separation
distance of at least 68.7cm (~27.1 inches) between the antenna connected to the RF booster and the
human user’s body within the area
. (VSWR ≤ 2:1, Zo= 50 ohms and a cable attenuation less then 1dB).
.