SendFar Technology Co. Ltd. WPC-02005 Manuel D’Utilisation

 

23

 

Radio Data Rate 11, 5.5, 2 and 1 Mbps, Auto Fallback 
Operating Voltage 3.3V/5V 
Regulation Certifications FCC Part 15/UL, ETSI 300/328/CE 
Compatibility Fully interoperable with IEEE802.11b compliant products 
LED Indicator RF Link activity 

 

Network Architecture Support ad-hoc, peer-to-peer networks and 
infrastructure communications to wired Ethernet networks via Access Point 
Drivers Windows 95/98/ME/2000/XP 
Access Protocol CSMA/CA 
Roaming IEEE802.11b compliant 
Security 64/128-bit WEP data encryption 

Frequency Band 2.4 – 2.484 GHz 
Radio Type Direct Sequence Spread Spectrum (DSSS) 
Modulation CCK (11, 5.5Mbps), DQPSK (2Mbps), DBPSK (1Mbps) 
Operation Channels 11 for North America, 14 for Japan, 13 for Europe, 2 
for Spain, 4 for France 
RF Output Power 19dBm (WPC-8110), 13dBm (WPC-2110) 
Sensitivity @FER=0.08 11 Mbps <-85dBm (WPC-8110), 83dBm(WPC-
2110) 
5.5 Mbps<-88dBm (WPC-8110), 86dBm (WPC-2110) 
2 Mbps <-91dBm (WPC-8110), 89dBm (WPC-2110) 
1 Mbps <-93dBm (WPC-8110), 91dBm (WPC-2110) 

 

Temperature Range 0 to 55 C (operating), -20 to 75 C (storage) 
Humidity (non-condensing) 10% to 95% typical 

 

Form Factor PCMCIA Type II PC Card 
Dimensions 118.5(L)mm * 54.5(W)mm * 9.2(H)mm 
Weight 45 g 
 

 

24

 

 

This device complies with Part 15 of FCC Rules and Canada RSS-210. 
Operation is subject to the following conditions: 

1.  This device may not cause harmful interference. 
2.  This device must accept any interference received, including interference that 

may cause undesired operation. 

3.  To comply with RF safety requirements, you must maintain a distance of 20 cm 

from the antenna when operating the device. 

4.  This transmitter must not be co-located or operating in conjunction with any 

other antenna or transmitter. 

 

This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules, These limits 
are designed to provide reasonable protection against harmful interference 
in a residential installation. This equipment generates, uses and can radiate 
radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to 
radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the 
interference by one of the following measures:  
 

 

Reorient or relocate the receiving antenna. 

 

Increase the separation between the equipment and receiver. 

 

Connect the equipment into an outlet on a circuit different from that to 
which the receiver is connected. 

 

Consult the dealer or an experienced radio/TV technician for help. 

 

To assure continued compliance, (example – use only shielded interface 
cables when connecting to computer or peripheral devices). Any changes 
or modifications not expressly approved by the party responsible for 
compliance could void the user’s authority to operate this equipment. 
 
 
Manufacturer’s Declaration of Conformity