Gigawit Electronics Limited GWBMA3X Manuel D’Utilisation
QECGWBMA3X
ORIGINAL EQUIPMENT MANUFACTURER (OEM) NOTES
The OEM must certify the final end product to comply with unintentional radiators (FCC Sections 15.107 and
15.109) before declaring compliance of the final product to Part 15 of the FCC rules and regulations. Integration
into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change.
into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change.
The OEM must comply with the FCC labeling requirements. If the module’s label is not visible when installed,
then an additional permanent label must be applied on the outside of the finished product which states:
“Contains transmitter module FCC ID:
“Contains transmitter module FCC ID:
Additionally, the following statement should be included
on the label and in the final product’s user manual: “This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not cause harmful interferences, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.”
Operation is subject to the following two conditions: (1) This device may not cause harmful interferences, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.”
The module is limited to installation in mobile or fixed applications. Separate approval is required for all other
operating configurations, including portable configuration with respect to Part 2.1093 and different antenna
configurations.
configurations.
A module or modules can only be used without additional authorizations if they have been tested and granted
under the same intended end‐use operational conditions, including simultaneous transmission operations.
When they have not been tested and granted in this manner, additional testing and/or FCC application filing
may be required. The most straightforward approach to address additional testing conditions is to have the
grantee responsible for the certification of at least one of the modules submit a permissive change application.
When having a module grantee file a permissive change is not practical or feasible, the following guidance
provides some additional options for host manufacturers. Integrations using modules where additional testing
and/or FCC application filing(s) may be required are: (A) a module used in devices requiring additional RF
exposure compliance information (e.g., MPE evaluation or SAR testing); (B) limited and/or split modules not
meeting all of the module requirements; and (C) simultaneous transmissions for independent collocated
transmitters not previously granted together.
When they have not been tested and granted in this manner, additional testing and/or FCC application filing
may be required. The most straightforward approach to address additional testing conditions is to have the
grantee responsible for the certification of at least one of the modules submit a permissive change application.
When having a module grantee file a permissive change is not practical or feasible, the following guidance
provides some additional options for host manufacturers. Integrations using modules where additional testing
and/or FCC application filing(s) may be required are: (A) a module used in devices requiring additional RF
exposure compliance information (e.g., MPE evaluation or SAR testing); (B) limited and/or split modules not
meeting all of the module requirements; and (C) simultaneous transmissions for independent collocated
transmitters not previously granted together.
This Module is full modular approval, it is limited to OEM installation ONLY.
Integration into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change.
(OEM) Integrator has to assure compliance of the entire end product incluld the integrated Module.
Additional measurements (15B) and/or equipment authorizations (e.g Verification) may need to be addressed
depending on co-location or simultaneous transmission issues if applicable.
Note: (OEM) Integrator assure the compliance of FCC requirements, please make sure the module(s) is installed
and fully operational, or contact us for technical support.
(OEM) Integrator is reminded to assure that these installation instructions will not be made available to the end user
of the final host device.
Integration into devices that are directly or indirectly connected to AC lines must add with Class II Permissive Change.
(OEM) Integrator has to assure compliance of the entire end product incluld the integrated Module.
Additional measurements (15B) and/or equipment authorizations (e.g Verification) may need to be addressed
depending on co-location or simultaneous transmission issues if applicable.
Note: (OEM) Integrator assure the compliance of FCC requirements, please make sure the module(s) is installed
and fully operational, or contact us for technical support.
(OEM) Integrator is reminded to assure that these installation instructions will not be made available to the end user
of the final host device.