Demarc Technology Group LLC DT100 Manuel D’Utilisation
FCC ID NO: QGK-DT-100
Demarc Technology Group, LLC
40 Fairview Rd – Frenchtown NJ, 08825
Tel: 908-996-7995 Fax: 908-847-0202
40 Fairview Rd – Frenchtown NJ, 08825
Tel: 908-996-7995 Fax: 908-847-0202
Website: http:/// www.demarctech.com
Email: info@demarctech.com
Email: info@demarctech.com
FCC Notice
Demarc Technology Group, LLC wireless equipment described herein complies with FCC radiation
exposure limits set forth for an uncontrolled environment when installed as directed. The equipment should
be installed and operated as fix-mounted system such that the main lobe(s) of these antennas are located a
minimum of 8 feet between the antenna and all persons during normal operation.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
exposure limits set forth for an uncontrolled environment when installed as directed. The equipment should
be installed and operated as fix-mounted system such that the main lobe(s) of these antennas are located a
minimum of 8 feet between the antenna and all persons during normal operation.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
2. This device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
Federal Communications Commission (FCC) Statement
This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
FCC Output Power Restrictions
The FCC does not require licensing to implement this device. However, the FCC has established
restrictions regarding maximum output power and the adjustments required when employing directional
gain antennas. These restrictions are detailed in FCC Part 15.247 (b)(1), (b)(3)(i), and (3)(iii). It is the
responsibility of the individuals designing and implementing the radio system to assure compliance with
these and any other pertinent FCC Rules and Regulations.
restrictions regarding maximum output power and the adjustments required when employing directional
gain antennas. These restrictions are detailed in FCC Part 15.247 (b)(1), (b)(3)(i), and (3)(iii). It is the
responsibility of the individuals designing and implementing the radio system to assure compliance with
these and any other pertinent FCC Rules and Regulations.
FCC RF Radiation Exposure Statement:
The DT-ZM-100mW-WC is designed for 2.4 GHz @ 100mW. This level of RF energy are below the
Maximum Permissible Exposure (MPE) levels specified in FCC OET 65:97-01. This is only approved
with the antenna gains as listed in this document with the maximum antenna gain of 15.7dBi. A separation
distance of 25 cm between the antenna and humans must be maintained.
Maximum Permissible Exposure (MPE) levels specified in FCC OET 65:97-01. This is only approved
with the antenna gains as listed in this document with the maximum antenna gain of 15.7dBi. A separation
distance of 25 cm between the antenna and humans must be maintained.
The following precautions must be taken during installation of this equipment:
• The installed antenna must not be located in a manner that allows exposure of the general
population to the direct beam path of the antenna at a distance less than 25cm. Installation on
towers, masts, or rooftops not accessible to the general population is recommended; or
towers, masts, or rooftops not accessible to the general population is recommended; or
• Mount the antenna in a manner that prevents any personnel from entering the area within 25
cm from the front of the antenna.
• During antenna installation, be sure that power to the DT-ZM-100mW-WC equipment is
turned off in order to prevent any energy presence on the coaxial connector.
• During installation and alignment of the antenna, do not stand in front of the antenna
assembly.
•
During installation and alignment of the antenna, do not handle or touch the front of the
antenna.
antenna.
These simple precautions must be taken to prevent personnel from exposure to RF energy in excess of
specified MPE levels.